Symphonic TV DVD Combo SC520FDF User Manual

OWNER’S  
MANUAL  
COLOR TV/DVD  
(20 inch)  
SC520FDF  
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.  
If you need additional operating assistance after reading this owner’s  
manual or to order replacement accessories, please call  
TOLL FREE : 1-800-242-7158.  
Or visit our WEB SITE at http://www.Symphonic.us  
Please read before using this equipment  
 
FIGURE A  
EXAMPLE OF ANTENNA GROUNDING AS PER  
NATIONAL ELECTRICAL CODE  
ANTENNA  
LEAD I N  
WI RE  
GROUND  
CL AMP  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
ELECTRI C  
SERVICE  
EQUIPMENT  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
NEC  
-
NATIONAL ELECTRICAL CODE  
POWER SERVICE GROUNDING  
ELECTRODE SYSTEM  
(NEC ART 250, PART H)  
S2898A  
13. Outdoor Antenna grounding - If an outside antenna or  
cable system is connected to the unit, be sure the anten-  
na or cable system is grounded so as to provide some  
protection against voltage surges and built-up static  
charges. Article 810 of the National Electrical Code,  
ANSI/NFPA No. 70, provides information with respect  
to proper grounding of the mast and supporting struc-  
ture, grounding of the lead-in wire to an antenna dis-  
charge unit, size of grounding conductors, location of  
antenna-discharge unit, connection to grounding elec-  
trodes, and requirements for the grounding electrode.  
(Fig. A)  
19. Damage Requiring Service - Unplug this unit from the  
wall outlet and refer servicing to qualified service per-  
sonnel under the following conditions:  
a. When the power-supply cord or plug is damaged or  
frayed.  
b. If liquid has been spilled, or objects have fallen into the  
unit.  
c. If the unit has been exposed to rain or water.  
d. If the unit does not operate normally by following the  
operating instructions. Adjust only those controls that are  
covered by the operating instructions, as improper  
adjustment of other controls may result in damage and  
will often require extensive work by a qualified techni-  
cian to restore the unit to its normal operation.  
14. Lightning - For added protection for this unit receiver  
during a lightning storm, or when it is left unattended  
and unused for long periods of time, unplug it from the  
wall outlet and disconnect the antenna or cable system.  
This will prevent damage to the unit due to lightning and  
power-line surges.  
e. If the unit has been dropped or damaged in any way.  
f. When the unit exhibits a distinct change in performance,  
this indicates a need for service.  
15. Power Lines - An outside antenna system should not be  
located in the vicinity of overhead power lines or other  
electric light or power circuits, or where it can fall into  
such power lines or circuits. When installing an outside  
antenna system, extreme care should be taken to keep  
from touching such power lines or circuits as contact  
with them might be fatal.  
20. Replacement Parts - When replacement parts are  
required, be sure the service technician has used replace-  
ment parts specified by the manufacturer that have the  
same characteristics as the original part. Unauthorized  
substitutions may result in fire, electric shock, injury to  
persons or other hazards.  
21. Safety Check - pon completion of any service or repairs  
to this unit, ask the service technician to perform routine  
safety checks to determine that the unit is in proper  
operating condition.  
16. Overloading - Do not overload wall outlets and exten-  
sion cords as this can result in a risk of fire or electric  
shock.  
17. Object and Liquid Entry - Never push objects of any  
kind into this unit through openings as they may touch  
dangerous voltage points or short out parts that could  
result in a fire or electric shock. Never spill liquid of any  
kind on the unit.  
22. Heat - This unit product should be situated away from  
heat sources such as radiators, heat registers, stoves, or  
other products (including amplifiers) that produce heat.  
18. Servicing - Do not attempt to service this unit yourself  
as opening or removing covers may expose you to dan-  
gerous voltage or other hazards. Refer all servicing to  
qualified service personnel.  
- 3 -  
EN  
 
PRECAUTIONS  
LASER SAFETY  
IMPORTANT COPYRIGHT INFORMATION  
Unauthorized copying, broadcasting, public perfor-  
mance and lending of discs are prohibited.  
This product incorporates copyright protection tech-  
nology that is protected by U.S. patents and other  
intellectual property rights. Use of this copyright  
protection technology must be authorized by  
Macrovision, and is intended for home and other  
limited viewing uses only unless otherwise autho-  
rized by Macrovision. Reverse engineering or dis-  
assembly is prohibited.  
This unit employs a laser. Only a qualified service  
person should remove the cover or attempt to ser-  
vice this device, due to possible eye injury.  
CAUTION: USE OF CONTROLS OR ADJUST-  
MENTS OR PERFORMANCE OF PROCE-  
DURES OTHER THAN THOSE SPECIFIED  
HEREIN MAY RESULT IN HAZARDOUS  
RADIATION EXPOSURE.  
FCC WARNING- This equipment may gener-  
ate or use radio frequency energy. Changes or  
modifications to this equipment may cause  
harmful interference unless the modifications  
are expressly approved in the instruction man-  
ual. The user could lose the authority to oper-  
ate this equipment if an unauthorized change  
or modification is made.  
CAUTION: VISIBLE AND INVISIBLE LASER  
RADIATION WHEN OPEN AND INTERLOCK  
DEFEATED. DO NOT STARE INTO BEAM.  
LOCATION: INSIDE, NEAR THE DECK  
MECHANISM.  
RADIO-TV INTERFERENCE  
This Class B digital apparatus complies with  
Canadian ICES-003.  
This equipment has been tested and found to com-  
ply with the limits for a Class B digital device, pur-  
suant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against  
harmful interference in a residential installation.  
This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause  
harmful interference to radio communications.  
However, there is no guarantee that interference  
will not occur in a particular installation. If this  
equipment does cause harmful interference to  
radio or television reception, which can be deter-  
mined by turning the equipment off and on, the  
user is encouraged to try to correct the interfer-  
ence by one or more of the following measures:  
1) Reorient or relocate the receiving antenna.  
2) Increase the separation between the equipment  
and receiver.  
Cet appareil numérique de la classe B est  
conforme à la norme NMB-003 du Canada.  
CAUTION: TO PREVENT ELECTRIC SHOCK,  
MATCH WIDE BLADE OF PLUG TO WIDE  
SLOT, FULLY INSERT.  
ATTENTION: POUR ÉVITER LES CHOC  
ÉLECTRIQUES, INTRODUIRE LA LAME LA  
PLUS LARGE DE LA FICHE DANS LA  
BORNE CORRESPONDANTE DE LA PRISE  
ET POUSSER JUSQU’AU FOND.  
A NOTE ABOUT RECYCLING  
Batteries should never be thrown away or inciner-  
ated but disposed of in accordance with your local  
regulations concerning chemical wastes.  
3) Connect the equipment into an outlet on a cir-  
cuit different from that to which the receiver is  
connected.  
4) Consult the dealer or an experienced radio/TV  
technician for help.  
The serial number of this product may be found on the back of the unit. No other unit has the same serial  
number as yours. You should record the number and other vital information here and retain this book as a per-  
manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.  
Date of Purchase  
Dealer Purchase from  
Dealer Address  
Dealer Phone No.  
Model No.  
Serial No.  
- 4 -  
EN  
 
WARNING  
LOCATION  
Moisture condensation may occur inside the unit  
when it is moved from a cold place to a warm place  
or after heating a cold room or under conditions of  
high humidity. If a DVD is played in a unit which has  
moisture, it may damage the DVD and the unit.  
Therefore when the condensation occurs inside the  
unit, turn the unit on and allow at least 2 hours for the  
unit to dry out.  
For safe operation and satisfactory performance of  
your unit, keep the following in mind when selecting  
a place for its installation:  
Shield it from direct sunlight and keep it away from  
sources of intense heat.  
Avoid dusty or humid places.  
Avoid places with insufficient ventilation for proper  
heat dissipation. Do not block the ventilation holes at  
the top or bottom of the unit. Do not place the unit  
on a carpet because this will block the ventilation  
holes.  
SYMBOLS USED IN THIS MANUAL  
The following symbols below appear in some head-  
ings and notes in this manual, with the following  
meanings.  
Install unit in a horizontal position.  
Avoid locations subject to strong vibration.  
Do not place the unit near strong magnetic fields.  
Avoid moving the unit to locations where tempera-  
TV  
: Description refers to TV operation (in the TV mode).  
ture differences are extreme.  
DVD-V  
Be sure to remove disc and unplug the AC power  
cord from the outlet before carrying the unit.  
: Description refers to playback of DVD video discs  
(in the DVD mode).  
AVOID THE HAZARDS OF  
CD  
ELECTRICAL SHOCK AND FIRE  
: Description refers to playback of Audio CDs  
(in the DVD mode).  
Do not handle the power cord with wet hands.  
Do not pull on the power cord when disconnecting  
it from an AC wall outlet. Grasp it by the plug.  
If by accident, water is spilled on your unit, unplug  
the power cord immediately and take the unit to our  
Authorized Service Center for servicing.  
QUICK  
: Description refers to the items to be set by the  
QUICK mode (in the DVD mode).  
Do not put your fingers or objects into the unit disc  
loading tray.  
Do not place anything directly on top of the unit.  
SUPPLIED ACCESSORIES  
Remote Control Unit  
Batteries  
Owner’s Manual  
Owner's Manual  
( NE207UD )  
2 AA Batteries  
( 1EMN20326 )  
If you need to replace these accessories, please refer to the PART NO. under the illustrations and call our  
help line mentioned on the front page.  
Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators  
(Splitter). Contact your local electronics store for these items.  
- 5 -  
EN  
 
TABLE OF CONTENTS  
DVD SECTION  
C IMPORTANT SAFEGUARDS . . . . .2  
C CHANGING THE DVD SET UP  
ITEMS . . . . . . . . . . . . . . . . . . . . . . .26  
C PRECAUTIONS . . . . . . . . . . . . . . . .4  
C ABOUT THE DISCS . . . . . . . . . . . .19  
PLAYABLE DISCS . . . . . . . . . . . .19  
UNPLAYABLE DISCS . . . . . . . . . .19  
CUSTOM MENU . . . . . . . . . . . . . .26  
LANGUAGE SETTING . . . . . . . .26  
DISPLAY SETTING . . . . . . . . . .27  
AUDIO SETTING . . . . . . . . . . . .27  
PARENTAL CONTROL . . . . . . . .28  
OTHER SETTINGS . . . . . . . . . . .28  
INITIALIZE . . . . . . . . . . . . . . . . . .28  
LOCATION . . . . . . . . . . . . . . . . . . .5  
AVOID THE HAZARDS OF  
ELECTRICAL SHOCK AND FIRE .5  
C PLAYING A DISC . . . . . . . . . . . . . .20  
BASIC PLAYBACK . . . . . . . . . . . .20  
GENERAL FEATURES . . . . . . . . .20  
DISC MENU . . . . . . . . . . . . . . . . .20  
TITLE MENU . . . . . . . . . . . . . . . . .20  
RESUME . . . . . . . . . . . . . . . . . . . .21  
PAUSE . . . . . . . . . . . . . . . . . . . . . .21  
STEP BY STEP PLAYBACK . . . . .21  
WARNING . . . . . . . . . . . . . . . . . . . .5  
SYMBOLS USED IN THIS  
MANUAL . . . . . . . . . . . . . . . . . . . . .5  
C SUPPLIED ACCESSORIES . . . . . . .5  
C TABLE OF CONTENTS . . . . . . . . . .6  
C FEATURES . . . . . . . . . . . . . . . . . . . .7  
C TROUBLESHOOTING GUIDE . . .29  
C MAINTENANCE . . . . . . . . . . . . . . .32  
DISC HANDLING . . . . . . . . . . . . .32  
C OPERATING CONTROLS AND  
FUNCTIONS . . . . . . . . . . . . . . . . . . .8  
C SPECIFICATIONS . . . . . . . . . . . . .33  
C ESPAÑOL . . . . . . . . . . . . . . . . . . . .34  
C WARRANTY . . . . . . . . . . .Back Cover  
FAST FORWARD /  
FAST REVERSE . . . . . . . . . . . . . .21  
C PREPARATION FOR USE . . . . . . .10  
SLOW FORWARD /  
SLOW REVERSE . . . . . . . . . . . . . .21  
ANTENNA/CABLE  
CONNECTION . . . . . . . . . . . . . . . .10  
ZOOM . . . . . . . . . . . . . . . . . . . . . .21  
CONNECTING TO FRONT A/V  
C SEARCH FUNCTION . . . . . . . . . . .22  
TRACK SEARCH . . . . . . . . . . . . .22  
TITLE / CHAPTER SEARCH . . . .22  
TIME SEARCH . . . . . . . . . . . . . . .22  
MARKER SETUP SCREEN . . . . . .22  
INPUT JACKS . . . . . . . . . . . . . . . .11  
CONNECTING TO A STEREO  
AMPLIFIER EQUIPPED WITH  
DIGITAL INPUT JACKS (for DVD)11  
CONNECTING TO A DOLBY  
DIGITAL DECODER (for DVD) . .12  
INSTALLING THE BATTERIES . .12  
C
SPECIAL PLAYBACK FUNCTION . .23  
REPEAT . . . . . . . . . . . . . . . . . . . . .23  
PROGRAM . . . . . . . . . . . . . . . . . . .23  
RANDOM PLAYBACK . . . . . . . . .23  
TV SECTION  
C TV OPERATION AND SETTINGS .13  
WATCHING A TV PROGRAM . . .13  
DEGAUSSING . . . . . . . . . . . . . . . .13  
PICTURE CONTROL . . . . . . . . . . .13  
SLEEP TIMER . . . . . . . . . . . . . . . .14  
CLOSED CAPTION SYSTEM . . . .14  
CHANNEL SET UP . . . . . . . . . . . .15  
V-CHIP SET UP . . . . . . . . . . . . . . .16  
TV RATING SET UP . . . . . . . . .16  
MPAA RATING SET UP . . . . . .17  
CHANGE ACCESS CODE . . . . .17  
MENU LANGUAGE . . . . . . . . . . .17  
C CHANGING THE SETTINGS . . . .24  
SUBTITLE LANGUAGE . . . . . . . .24  
AUDIO LANGUAGE . . . . . . . . . . .24  
STEREO SOUND MODE . . . . . . . .24  
CAMERA ANGLE . . . . . . . . . . . . .24  
BLACK LEVEL SETTING . . . . . . .24  
VIRTUAL SURROUND . . . . . . . . .25  
C
THE ON-SCREEN INFORMATION . .25  
C CABLE CHANNEL  
DESIGNATIONS . . . . . . . . . . . . . .18  
- 6 -  
EN  
 
FEATURES  
TV Mode  
Infrared remote control  
Trilingual on screen TV setup display selectable  
in English, Spanish or French  
181 channel capability PLL frequency synthesiz-  
er tuner with direct station call (A converter may  
be necessary to view scrambled cable channels.)  
Closed Caption Decoder – You may view special-  
ly labeled (cc) TV programs, movies, news, etc.  
with either a dialogue caption or text display added  
to the program.  
Auto power off system – If there is no air signal  
input from the antenna terminal and no operation  
for 15 minutes, the unit will turn itself off automat-  
ically.  
Sleep timer – Allows you to have the unit auto-  
matically turn off at a desired time.  
V-CHIP – Enables parents to prevent their children  
from watching inappropriate material on TV.  
DVD Mode  
¡Dolby Digital sound  
¡Parental lock  
This unit can handle Dolby Digital surround sound  
having 5.1 channels when connected to a Dolby  
Digital decoder.  
You can set the control level to limit playback of  
discs which may not be suitable for children.  
¡Automatic detection of discs  
This unit automatically detects if the loaded disc is  
DVD or Audio CD.  
¡Still/fast/slow/step playback  
Various playback modes are available including  
still pictures, fast forward/reverse, slow motion and  
step frames.  
¡On-screen display  
Information about the current operation can be  
displayed on a TV screen, allowing you to confirm  
the currently active functions (such as program  
playback), on the TV screen using the remote  
control.  
¡Random playback for Audio CD  
This unit can shuffle the order of tracks to play  
them in random order.  
¡Program playback for Audio CD  
You can program the order of tracks to play them in  
any desired order.  
¡Search  
Chapter search / Title search / Track search / Time  
search  
¡DVD menus in a desired language  
You can display DVD menus in a desired language,  
if available on a DVD.  
¡Repeat  
Chapter / Title / Track / All / A-B  
¡Zoom  
¡Screen saver/Auto power-off functions  
The screen saver program starts when there is no  
input from the unit for 5 minutes in the stop mode.  
After the screen saver program is activated for 15  
minutes, the power automatically turns off.  
Magnified screen can be displayed.  
¡Marker  
The part designated by user can be called back.  
¡Resume Play  
User can resume to playback from the part at which  
the play was stopped.  
¡Subtitles in a desired language  
You can select a desired language for the display  
subtitles, if that language is available on a disc.  
¡Virtual Surround  
¡Selecting a camera angle  
You can select the desired camera angle, if a disc  
contains sequences recorded from different angles.  
¡Bit rate indication  
¡DRC (Dynamic range control)  
You can control the range of sound volume.  
¡Choices for audio language and sound mode  
You can select the desired audio language and  
sound mode, if different languages and modes are  
available on a disc.  
- 7 -  
EN  
 
OPERATING CONTROLS AND FUNCTIONS  
- FRONT PANEL - [Fig.1]  
OPEN/  
POWER  
VOLUME  
CHANNEL  
STOP  
SKIP  
PLAY  
SKIP  
PAUSE CLOSE  
VIDEO  
L–AUDIO–R  
–SEARCH–  
HEADPHONE  
1
2
3
4
5
6
7 8 9 10 9 1112 13  
7.Remote sensor window  
8.STOP C Button [P.20]  
Stops operation of the disc.  
[Fig. 2]  
- REMOTE CONTROL -  
9.SKIP H / G Buttons [P.22]  
Press once to skip chapters or tracks to a desired  
point.  
OPEN/  
POWER PICTURE SELECT  
CLOSE  
4
12  
35  
E
D
SEARCH  
/
Buttons (Front panel) [P.21]  
14  
1
4
2
5
8
0
3
6
Press and hold to change forward or reverse  
playback speed.  
CH.  
6
15  
16  
10. PLAY B Button [P.20]  
7
SLEEP  
9
+100  
Starts playback of the disc.  
VOL.  
5
11. PAUSE F Button [P.21]  
Pauses the current disc operation.  
12. OPEN/CLOSE A Button [P.20]  
Hit to insert a disc into or remove it from the  
tray.  
+10  
SKIP  
ZOOM  
MUTE  
34  
33  
32  
9
10  
PLAY  
STOP  
REV  
FWD  
13. HEADPHONE Jack  
8
DISC  
MENU  
To connect headphone (not supplied) for personal  
listening.  
PAUSE SLOW  
DISPLAY  
11  
17  
31  
14. PICTURE Button [P.13]  
ENTER  
30  
29  
28  
Hit to adjust the picture.  
SETUP  
TITLE  
RETURN  
18  
19  
20  
15. Number Buttons  
CLEAR SEARCH MODE REPEAT  
A-B  
TV Mode: [P.13]  
Press two digits to directly access the desired  
channel.  
Remember to hit [0] before a single digit channel.  
+100 Button–  
Hit to select cable channels which are higher  
than 99.  
DVD Mode: [P.22]  
Hit to enter the desired number.  
+10 Button–  
Hit to enter the desired numbers which are higher  
than 9.  
27  
AUDIO SUBTITLE ANGLE  
MODE  
21  
22  
23  
26  
25  
24  
1.Disc loading tray  
2.VIDEO input Jack  
Connect to the video output jack of a video camera or  
VCR.  
3.AUDIO L/R input Jacks  
Connect to the audio output jacks of a video camera or  
VCR.  
16. SLEEP Button [P.14]  
Sets the Sleep Timer.  
4.POWER Button [P.13]  
17. DISPLAY Button  
Hit to turn the power on and off.  
Buttons [P.13]  
Press to control the volume level for the DVD and TV.  
Buttons [P.13]  
Press to select memorized channels.  
TV Mode:  
K
L
5.VOLUME (VOL.)  
/
Displays the current channel number on the TV  
screen.  
DVD Mode: [P.25]  
K
L
6.CHANNEL (CH.)  
/
Displays the current status on the TV screen.  
- 8 -  
EN  
 
- REAR PANEL - [Fig.3]  
ANT.  
COAXIAL  
36 37  
38  
18. SETUP Button [P.26]  
K
L
{
B
30.  
/
/
/
Buttons  
Hit to enter or exit the setup menu of TV or DVD.  
TV Mode: [P.13]  
Press to select a setting mode from the menu on  
19. TITLE Button [P.20]  
the TV screen.  
Displays the title menu.  
Press to select or adjust from a particular menu.  
DVD Mode: [P.20]  
Press to select a menu item.  
20. CLEAR Button [P.22]  
Hit to clear or cancel a setting currently entered.  
21. MODE Button [P.23, 24, 25]  
31. DISC MENU Button [P.20]  
Hit to call up the program screen or the random  
screen in the stop mode.  
Calls up the DVD menu.  
E
32. REV  
Button [P.21]  
Hit to call up the Black Level Setting screen or  
the Virtual Surround screen during playback.  
Hit to view the DVD picture in fast reverse or  
slow reverse motion.  
22. SEARCH MODE Button [P.22]  
D
FWD  
Button [P.21]  
Hit to locate a desired point.  
Hit to view in fast or slow forward motion.  
23. AUDIO Button [P.24]  
33. ZOOM Button [P.21]  
Hit to select a desired audio language or sound  
mode.  
Enlarges part of a DVD-reproduced image.  
34. MUTE Button [P.13]  
24. SUBTITLE Button [P.24]  
Mutes the sound. Hit it again to restore sound.  
Hit to select a desired subtitle language.  
35. SELECT Button [P.11]  
25. REPEAT Button [P.23]  
Hit to change to TV mode, external input mode or  
DVD mode.  
Repeats playback of the current disc, title, chap-  
ter, or track.  
36. COAXIAL Jack [P.11]  
26. ANGLE Button [P.24]  
Connect to the digital input of an external  
amplifier or decoder (for DVD Audio only).  
Hit to change the camera angle to see the  
sequence being played back from a different angle  
(if available).  
37. ANT(ENNA). Jack [P.10]  
Connect to an antenna, cable system or satellite  
system.  
27. A-B Button [P.23]  
Repeats playback of a selected section.  
38. Power cord [P.13]  
28. RETURN Button [P.22]  
Connect to a standard AC outlet (120V/60Hz).  
Returns to the previous screen in the setup menu.  
NOTE:  
29. ENTER Button [P.15]  
Remove the power cord from the hook to avoid  
breaking a wire before you connect to a standard  
AC outlet.  
Hit to accept a setting.  
NOTE:  
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with  
a universal remote control.  
If you decide to use a universal remote control with this unit, please be aware that the code number given  
may not operate this unit. In this case, please call the manufacturer of the universal remote control.  
- 9 -  
EN  
 
PREPARATION FOR USE  
ANTENNA/CABLE CONNECTIONS  
Plug the incoming cable into the ANT. jack on the rear of the unit.  
If your cable service supplies you with a converter box or if you use a  
satellite system, connect the box with this unit as shown below.  
Cable  
TV signal  
Antenna  
or  
Incoming cable from home Antenna /  
Cable Company (No Cable Box)  
ANT.  
COAXIAL  
Rear of the unit  
ANT.  
Cable Box or  
Satellite Box*  
OR  
OUT  
IN  
[Fig. 4]  
Incoming cable from Cable Company  
or Satellite Antenna  
*NOTE (DO NOT DISCONNECT FROM BOX)  
Some cable TV systems use scrambled signals and  
require a special converter to receive these channels.  
Consult your local cable company.  
Note to CATV system installer:  
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides  
guidelines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding  
system of the building as close to the point of cable entry as practical.  
Bent pin  
NOTE:  
Before plugging the antenna into the ANT. jack of the unit, check that the pin is  
not bent. If it is bent, straighten the pin as illustrated, then plug the pin into the  
ANT. jack of the unit.  
Cable  
Plug  
(Needs to be  
straightened)  
(Straight pin)  
For your safety and to avoid damages to the unit, unplug the antenna cable from the ANT. jack  
before moving the unit.  
- 10 -  
EN  
 
CONNECTING TO FRONT A/V INPUT JACKS  
When you watch a program recorded on another source (VCR or video camera), use the  
AUDIO/VIDEO input jacks on the front of the unit.  
AUX  
Connect the Audio/Video output jacks of another source to the AUDIO L/R and VIDEO  
jacks of this unit.  
K
L
Then press [SELECT] or [CH.  
/
] until “AUX” appears on the screen.  
OPEN/  
POWER  
VOLUME  
CHANNEL  
STOP  
SKIP  
PLAY  
SKIP  
PAUSE  
CLOSE  
VIDEO  
L–AUDIO–R  
E
–SEARCH–  
D
HEADPHONE  
ex.  
VCR or video camera, etc.  
To the Audio output jacks  
Audio Cable  
(commercially available)  
(IN)  
(OUT)  
(OUT)  
VIDEO  
L–AUDIO–R  
[Front of the unit]  
To the Video output jack  
Video Cable  
(commercially available)  
(IN)  
[Fig. 5]  
NOTE:  
When you connect a monaural VCR (another source) to this unit, connect the Audio output jack of the  
monaural VCR (another source) to the AUDIO L jack of this unit. The audio will output in both L and R  
channel equally.  
CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH  
DIGITAL INPUT JACKS (for DVD)  
Use an audio coaxial digital cable (commercially available) for the audio connections.  
Connect to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.  
ANT.  
COAXIAL  
ex.  
MD deck, DAT deck, etc.  
To COAXIAL jack  
(Only DVD AUDIO OUT)  
(OUT)  
To Coaxial digital  
Audio input jack  
Audio coaxial digital cable  
(commercially available)  
[Fig. 6]  
(IN)  
NOTES:  
The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital  
sound by an MD or DAT deck.  
Be sure to turn off the power to all components in the system before connecting another component.  
Refer to the Owner’s Manuals for the components to be connected to the unit.  
Set “DOLBY DIGITAL” to “PCM” for audio output in the setup mode. Playing a unit using incorrect set-  
tings may generate noise distortion and may also damage the speakers. (Refer to page 27.)  
- 11 -  
EN  
 
CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)  
If using this unit to play a DVD disc in a 5.1 channel Dolby Digital surround format, the unit outputs a  
DOLBY DIGITAL Data stream from its COAXIAL jack. By hooking the unit up to a Dolby Digital decoder,  
you can enjoy a more convincing, realistic ambience with powerful and high-quality surround sound as  
enjoyed in movie theaters.  
Use audio coaxial digital cables (commercially available) for the audio connections.  
Center  
speaker  
ANT.  
COAXIAL  
Front speaker  
(left)  
Front speaker  
(right)  
To COAXIAL jack  
(Only DVD AUDIO OUT)  
(OUT)  
Dolby Digital  
decoder  
To Coaxial digital  
Audio input jack  
Audio Coaxial digital cable  
(commercially available)  
Subwoofer  
Surround  
speaker  
(left)  
Surround  
speaker  
(right)  
(IN)  
[Fig. 7]  
NOTES:  
Be sure to turn off the power to all components in the system before connecting another component.  
Refer to the Owner’s Manuals for the components to be connected to the unit.  
If connected to a Dolby Digital decoder, set “DOLBY DIGITAL” to “BITSTREAM” for audio output in the  
setup mode. (Refer to page 27.)  
Unless connected to a Dolby Digital decoder, set “DOLBY DIGITAL” to “PCM” for audio output in the  
setup mode. Playing a unit using incorrect settings may generate noise distortion and may also damage the  
speakers. (Refer to page 27.)  
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are  
trademarks of Dolby Laboratories.  
INSTALLING THE BATTERIES  
1)Open the battery compartment cover by pressing  
the cover on the remote unit in the direction of the  
arrow.  
2)Insert 2 “AA” penlight batteries into the battery  
compartment in the direction indicated by the  
polarity (+/-) markings.  
[BATTERY PRECAUTIONS]  
Be sure to follow the correct polarity as indicated  
in the battery compartment. Reversed batteries  
may cause damage to the device.  
Do not mix different types of batteries together  
(e.g. Alkaline and Carbon-Zinc) or old batteries  
with fresh ones.  
3)Replace the cover.  
If the device is not to be used for a long period of  
time, remove the batteries to prevent damage or  
injury from possible battery leakage.  
Do not try to recharge batteries not intended to be  
recharged; they can overheat and rupture.  
- 12 -  
EN  
 
TV SECTION  
TV OPERATION AND SETTINGS  
WATCHING A TV PROGRAM  
DEGAUSSING  
TV  
This television has a degaussing circuit that will clear  
up color errors on the TV screen that are caused by  
any excess magnetism which happens to get too close  
to the TV. This circuit is designed to operate once  
when the set is first plugged in. If minor color  
errors are seen in some locations on the screen,  
please unplug the TV for approximately 30 min-  
utes. When the TV is plugged back in, the degauss-  
ing circuit will operate once to clear them up. Repeat  
this procedure any time the TV screen is accidentally  
magnetized or when the TV is moved or relocated.  
TV  
1 Plug in the unit power cord  
Plug the unit power cord into a standard  
AC outlet.  
NOTE:  
If any digits appear in the corner of the  
screen, hit [POWER] without unplug-  
ging the power cord.  
2 Turn on the unit  
Hit [POWER] to turn on the unit.  
PICTURE CONTROL  
TV  
3 Select the channel number  
K
L
Press [CH.  
/
] or the Number buttons to select  
The unit’s picture controls – BRIGHT, CON-  
TRAST, COLOR, TINT and SHARPNESS – are  
preset to factory specifications. Although they are  
usually the best, you may need to make some further  
adjustments for a more natural looking image.  
your desired channel number.  
Notes for using the Number buttons:  
¡You must precede single-digit channel numbers  
with a zero (for example: 02, 03, 04 and so on).  
¡When selecting cable channels which are higher  
than 99, hit [+100] first, then press the last two  
digits. (Example: to select channel 125, first hit  
[+100] then hit [2] and [5].)  
Make sure ...  
The unit must be turned on.  
1 Call up the menu  
4 Adjust sound  
Hit [PICTURE].  
X
Y
Press [VOL.  
/
] to adjust the  
volume.  
2 Select item you want to adjust  
VOLUME 20  
K
L
Hit [MUTE] to instantly mute the  
sound.  
Hit it again to restore the previous sound level.  
Press [  
/
] until desired control is displayed.  
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
BRIGHT  
CONTRAST  
COLOR  
NOTE:  
K
L
BRIGHT  
TINT  
SHARPNESS  
If you press [CH.  
/
] in the DVD mode, you  
P
P
P
P
P
P
P
C
P
P
P
P
P
P
P +  
can change the TV channels. Even if you turn off  
the unit in the DVD mode, when you turn it on  
again, it will go into the TV mode.  
3 Adjust the setting  
Press  
[s  
/
B
]
to adjust to your desired level within 5  
TO WATCH CABLE OR SATELLITE  
CHANNEL  
seconds.  
s
to decrease  
brightness  
to decrease  
contrast  
B
If the unit is connected to a cable box or satellite  
BRIGHT  
to increase  
brightness  
to increase  
contrast  
K
L
box, press [CH.  
/
] to select CH3 or CH4  
according to the output channel setting of the  
device and select desired channel on that device.  
CONTRAST  
COLOR  
TINT  
SHARPNESS to soft  
to pale  
to brilliant  
TO WATCH EXTERNAL INPUT  
to purple  
to green  
to clear  
When an external equipment is connected to the  
front AUDIO/VIDEO input jacks, press  
K
L
[SELECT] or [CH.  
/
] repeatedly until “AUX”  
Even if there is a power failure of any kind, the  
unit will retain its memory for this feature.  
appears on the screen.  
- 13 -  
EN  
 
If the unit displays a black box on  
the TV screen, this means that the  
unit is set to the TEXT mode. To  
clear screen, select [CAPTION1],  
[CAPTION2] or [OFF].  
SLEEP TIMER  
TV  
The Sleep Timer function turns off the unit without  
using [POWER] after a desired period of time.  
Make sure ...  
The unit must be turned on.  
1 Call up the Sleep Timer Setting  
Hit [SLEEP] so that “SLEEP 0 MINUTE” appears.  
1 Select “CAPTION”  
Hit [SETUP].  
- TV SETUP -  
2 Set sleep time  
Hit [SLEEP] repeatedly until your  
desired sleep time appears.  
CHANNEL SET UP  
V-CHIP SET UP  
K
L
Press [  
/
] to point to  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
B
“CAPTION”.  
Each additional press will increase  
the time by 30 minutes up to 120  
SLEEP 120 MINUTE  
minutes.  
2 Select your desired caption mode  
Hit [ENTER] repeatedly until your  
desired caption menu appears.  
After 5 seconds, the Sleep Timer setting will disap-  
pear automatically.  
- TV SETUP -  
CHANNEL SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [CAPTION1]  
([CAPTION1], [CAPTION2],  
[TEXT1] or [TEXT2])  
B
TO CANCEL THE SLEEP TIMER  
Hit [SLEEP] to call up the Sleep Timer Setting. Hit  
[SLEEP] repeatedly until “SLEEP 0 MINUTE”  
appears.  
3 Exit the caption setting mode  
Hit [SETUP] to exit the menu.  
NOTE:  
CLOSED CAPTION SYSTEM  
Even if there is a power failure of any kind, the  
unit will retain its memory for this feature.  
TV  
You can view specially labeled (cc) TV programs,  
movies, news and pre-recorded tapes with either a  
dialogue caption or text display.  
CAPTION mode: You can watch dramas, movies and  
news while captioning the dialogues and the contents  
of news.  
TO CANCEL THE CLOSED CAPTION  
SYSTEM  
Repeat steps 1 to 2 and select [OFF] using  
[ENTER]. Then hit [SETUP] to return to TV mode.  
TEXT mode: You can watch half screen text informa-  
tion if you want.  
1-2: You may get these captions or text information  
by selecting either “1” or “2”. Caption “2” is  
usually used for a second language if available.  
NOTES:  
Not all programs are broadcast with closed cap-  
tions. Your unit is designed to provide error free  
closed captions from high quality antenna, cable  
and VCR signals. Conversely, poor quality signals  
are likely to result in caption errors or no captions  
at all. Common signal conditions which may cause  
caption errors are listed below:  
Automobile ignition noise  
Electric motor brush noise  
Weak snowy reception on TV screen  
Multiplex signal reception displaying picture  
ghosts or airplane flutter  
- 14 -  
EN  
 
ADDING/DELETING CHANNELS  
The channels you no longer receive or seldom watch  
can be deleted from the memory. (Of course, you can  
add the deleted channel into the memory again.)  
CHANNEL SET UP  
Make sure ...  
TV  
The unit must be turned on.  
AUTO CHANNEL PROGRAMMING  
1 Select “CHANNEL SET UP”  
- TV SETUP -  
Hit [SETUP].  
As the initial setting, this unit has memorized all  
B
CHANNEL SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
K
L
]
Press  
[
/
to point to “CHAN-  
channels, including the ones not available in your  
area. This feature automatically puts only available  
channels into the memory.  
NEL SET UP”, then hit [ENTER].  
- TV SETUP -  
1 Select “CHANNEL SET UP”  
2 Select “ADD/DELETE CH”  
– CHANNEL SET UP –  
Hit [SETUP].  
K
L
B
CHANNEL SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
Press [  
/
] to point to  
B
ADD / DELETE CH (CATV)  
AUTO CH PROGRAMMING  
K
L
]
Press  
[
/
to point to  
“ADD/DELETE CH”, then hit  
[ENTER].  
“CHANNEL SET UP”, then hit  
[ENTER].  
2 Begin channel scanning  
3 Enter the desired channel number  
– CHANNEL SET UP –  
K
L
]
Press  
[
/
to point to “AUTO  
K
L
Press [CH.  
/
] or the Number  
ADD / DELETE CH (CATV)  
B AUTO CH PROGRAMMING  
CH PROGRAMMING”, then hit  
[ENTER].  
The tuner scans and memorizes all  
the active channels in your area.  
buttons until your desired channel  
08  
number appears. (You can also  
K
L
press [  
/
] to enter it.)  
ADD / DELETE  
You must precede single-digit  
channel numbers with a zero  
(Example: 02 ... 09).  
(Example: CH8)  
3 After scanning  
The tuner stops on the lowest memorized channel.  
NOTES:  
When “AUTO CH PROGRAM-  
MING” is activated where there  
is no TV signal input, “NO TV  
SIGNALS” will appear on the  
display after the completion of  
channel scanning.  
When selecting cable channels which are higher  
than 99, hit [+100] first, then press the last two  
digits. (Example: to select channel 125, first hit  
[+100] then hit [2] and [5].)  
NO TV SIGNALS  
4 Delete (or add) it from (or into) memory  
Hit [ENTER]. The channel number changes to light  
red. The channel is deleted from memory.  
The unit may recognize CATV channels to be TV  
To delete another channel, repeat steps 3 to 4.  
If you hit [ENTER] again, the channel is memo-  
rized again.  
channels if reception condition is poor. In this case,  
check the antenna connection and try “AUTO CH  
PROGRAMMING” again when reception condi-  
tions are better.  
Added channel : Light blue  
Deleted channel : Light red  
Channel memory programming is NOT neces-  
sary when connected to a cable box or satellite  
box. Just select the channel for cable box or  
satellite input (ex. CH3) on the unit, then select  
your desired channel on the cable box or satel-  
lite box.  
5 Exit the channel setup mode  
Hit [SETUP] to exit the menu.  
NOTE:  
To confirm that channel(s) has been deleted or  
K
L
added, press [CH.  
/
].  
- 15 -  
EN  
 
NOTES:  
V-CHIP SET UP  
When you select a rating and set  
it to [BLOCK], the higher ratings  
will be blocked automatically.  
The lower ratings will be avail-  
able for viewing.  
TV–Y  
TV–Y7  
TV–G  
TV–PG (DLSV )  
TV–14 (DLSV)  
TV–MA ( LSV)  
[VIEW]  
[VIEW]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
TV  
(
)
B
This feature enables parents to prevent their children  
from watching inappropriate material on TV. When  
you try to access a program which is blocked,  
“PROTECTED PROGRAM by ...” message appears  
on the TV screen.  
When you set the lowest rating to  
[VIEW], all other ratings will automatically be  
available for viewing.  
V-CHIP SET UP  
5 Setting “Sub-Ratings”  
Make sure ...  
TV–Y  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
When you select the ratings of  
B
TV–Y7  
TV–G  
(
)
The unit must be turned on.  
TV-Y7, TV-PG, TV-14 or TV-MA  
you will have the option of setting  
sub rating categories.  
TV–PG (  
)
)
)
TV–14  
(
TV–MA(  
1 Select “V-CHIP SET UP”  
Hit [SETUP].  
- TV SETUP -  
K
L
Press [  
/
] to select a rating with  
CHANNEL SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
sub-ratings you wish to block, then  
B
TV–Y7  
FV  
[BLOCK]  
[BLOCK]  
K
L
Press [  
/
] to select “V-CHIP  
B
hit [ENTER] twice.  
SET UP”, then hit [ENTER].  
K
L
Press [  
/
] to select a sub-rating,  
then hit [ENTER] to set it to  
[BLOCK] or [VIEW].  
2 Enter Access code  
Press the Number buttons to  
enter the access code.  
TV–PG  
[BLOCK]  
B
D
L
S
V
[BLOCK]  
[BLOCK]  
[BLOCK]  
[BLOCK]  
ACCESS CODE  
_
_
_
_
For the first time set-up or in the  
event the unit has lost power,  
enter the default code of 0000.  
Selection  
TV-Y7  
FV  
Rating Category Explanations  
Fantasy Violence  
3 Select the desired item  
TV-PG, TV-14, TV-MA  
K
L
Press [  
/
] to select “TV RATING”, “MPAA RAT-  
D
L
S
Suggestive Dialog (TV-PG, TV-14 only)  
Coarse Language  
Sexual Situation  
Violence  
ING” or “CHANGE CODE”, then hit [ENTER].  
Refer to the pages below to set up each item.  
– V-CHIP SET UP –  
A
P 16 Step  
P 17 Step  
4
4
4
V
B TV RATING  
MPAA RATING  
CHANGE CODE  
B
NOTE:  
The blocked sub-ratings will  
appear next to the rating category  
in the “TV RATING” menu.  
C
P 17 Step  
TV–Y  
TV–Y7  
TV–G  
TV–PG (DLSV)  
TV–14 (DLSV)  
TV–MA ( LSV)  
[VIEW]  
(
)
[VIEW]  
[VIEW]  
B
[BLOCK]  
[BLOCK]  
[BLOCK]  
A
TV RATING SET UP  
Follow steps to in the “V-CHIP SET UP” section  
1
3
above.  
6 Exit the V-Chip setting mode  
Hit [SETUP] to exit the menu.  
4 Blocking TV programs  
K
L
B
TV–Y  
TV–Y7  
TV–G  
TV–PG (  
TV–14  
TV–MA(  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
[VIEW]  
Press [  
/
] to select a rating that  
NOTE:  
(
)
you wish to block.  
Hit [ENTER] repeatedly to set it to  
[BLOCK] or [VIEW].  
)
)
)
To change the rating, the TV must  
(
PROTECTED PROGRAM  
by TV-Y  
be turned to an unprotected pro-  
gram. If “PROTECTED PRO-  
GRAM by ...” appears on the  
screen, please change the channel  
to a station that is not protected.  
Selection  
TV-Y  
Rating Category Explanations  
Appropriate for all children  
TV-Y7  
TV-G  
Appropriate for children seven and older  
General Audience  
TV-PG  
TV-14  
Parental Guidance suggested  
Unsuitable for children under 14  
TV-MA Mature audience only  
- 16 -  
EN  
 
B
MENU LANGUAGE  
MPAA RATING SET UP  
TV  
Follow steps to in the “V-CHIP SET UP” sec-  
tion on page 16.  
1
3
- TV SETUP -  
1 Select “LANGUAGE”  
Hit [SETUP].  
4 Select your desired item  
G
[VIEW]  
CHANNEL SET UP  
V-CHIP SET UP  
LANGUAGE [ENGLISH]  
CAPTION [OFF]  
K
L
Press [  
/
] to point to your  
PG  
[VIEW]  
PG–13  
R
NC–17  
X
[VIEW]  
B
K
L
Press [  
/
] to point to  
B
[BLOCK]  
[BLOCK]  
[BLOCK]  
desired item, then hit [ENTER] to  
select [BLOCK] or [VIEW].  
“LANGUAGE”.  
Selection  
G
PG  
PG-13  
R
Rating Category Explanations  
General Audience  
Parental Guidance suggested.  
Unsuitable for children under 13  
Restricted; under 17 requires accompa-  
nying parent or adult guardian  
No one under 17 admitted  
2 Select “ENGLISH”, “ESPAÑOLor “FRANÇAIS”  
Hit [ENTER] repeatedly to select “ENGLISH”,  
“ESPAÑOL”= Spanish or “FRANÇAIS”= French.  
3 Exit the Language mode  
Hit [SETUP] to exit the menu.  
NC-17  
X
Mature audience only  
NOTES:  
This function effects only the language on the  
screen menu and not the audio source.  
When you select a rating and set it to [BLOCK],  
the higher ratings will be blocked automatically.  
The lower ratings will be available for viewing.  
When you set the lowest rating to [VIEW], all  
other ratings will automatically be available for  
viewing.  
If for some reason the menu is in Spanish or  
K
L
French, hit [SETUP], press [  
/
] to point to  
“IDIOMA [ESPAÑOL]” or “LANGAGE  
[FRANÇAIS]”, then hit [ENTER] repeatedly to  
select desired language, then hit [SETUP].  
5 Exit the V-Chip setting mode  
Hit [SETUP] to exit the menu.  
C
CHANGE ACCESS CODE  
Follow steps to in the “V-CHIP SET UP” sec-  
1
3
tion on page 16.  
4 Enter New code  
NEW CODE  
Press the Number buttons to enter  
your desired access code in the  
“NEW CODE” space, then enter  
the same code in the “CONFIRM  
CODE” space. When completed,  
the menu will return to “V-CHIP SET UP”.  
X X X X  
CONFIRM CODE  
_
_
_
_
Make sure you enter exactly the same new code in  
the “CONFIRM CODE” space as one in the  
“NEW CODE” space. If they are different, the  
“NEW CODE” space is cleared for redoing.  
5 Exit the V-Chip setting mode  
Hit [SETUP] to exit the menu.  
NOTE:  
Your personal access code will be erased and will  
return to the default (0000) when a power failure  
occurs or when you turn off the power using a  
wall switch. If you have forgotten the code, unplug  
the power cord for 10 seconds to restore the access  
code to 0000.  
- 17 -  
EN  
 
CABLE CHANNEL DESIGNATIONS  
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels  
with letters or letter-number combinations. Please check with your local cable company. The following is a  
chart of common cable channel designations.  
CATV channel  
TV Display  
5A  
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10  
10  
11  
11  
12  
12  
13  
13  
A
B
14  
15  
CATV channel  
TV Display  
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
CATV channel  
R
S
T
U
V
W
W+1  
37  
W+2  
38  
W+3  
39  
W+4  
40  
W+5  
41  
W+6  
42  
W+7  
43  
W+8  
44  
W+9  
45  
TV Display  
31  
32  
33  
34  
35  
36  
CATV channel  
W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24  
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60  
W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39  
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75  
W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54  
TV Display  
CATV channel  
TV Display  
CATV channel  
TV Display  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
W+59 W+60 W+61 W+62 W+63 W+64  
100 101 102 103 104 105  
86  
87  
88  
89  
90  
W+55 W+56 W+57 W+58  
A-5  
95  
A-4  
96  
A-3  
97  
A-2  
98  
A-1  
99  
CATV channel  
TV Display  
91  
92  
93  
94  
CATV channel  
W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79  
TV Display  
106  
W+80 W+81 W+82 W+83 W+84  
121 122 123 124 125  
107  
108  
109  
110  
111  
112  
113  
114  
115  
116  
117  
118  
119  
120  
CATV channel  
TV Display  
- 18 -  
EN  
 
DVD SECTION  
ABOUT THE DISCS  
PLAYABLE DISCS  
Recorded  
Playable  
discs  
Disc size  
Region code  
Disc types  
Mark (logo)  
signals  
DVD-Video  
or  
* 1,2,4,6,10,11  
Example  
12 cm  
or  
8 cm  
Title 1  
Title 2  
DVD-RW  
DVD-R  
Digital video  
(MPEG2)  
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1  
Chapter 2  
-
-
-
* 1,3,4,5,6  
7,9,10  
DVD+RW  
DVD+R  
* 1,3,4,5,6,8,9,10  
Audio CD  
* 4,6,10  
Audio CD  
Example  
12 cm  
or  
8 cm  
Digital audio  
Track 1  
Track 2  
Track 5  
Track 6  
Track 3  
Track 4  
CD-RW  
CD-R  
* 4,5,6,9,10  
is a trademark of DVD Format/Logo Licensing Corporation.  
If you cannot play back a disc which bears one of the marks above, check the following notes.  
*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot  
be played back.  
*2: Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc’s producers.  
*3: Discs recorded in the VR (Video Recording) format cannot be played back.  
*4: Scratched or stained discs may not be played back.  
*5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the  
recorder or special properties of discs.  
*6: You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may not  
play them back. Even if they are played back, the sound or video quality will be compromised.  
*7: You may play back the unfinalized DVD-R/RW disc recorded in the video format on our brand’s DVD  
recorder. However, depending on the recording status of a disc, the disc may not be played back at all or  
normally (the picture or sound may not be smooth, etc.). In this case, you need to finalize the disc with  
the DVD recorder. Refer to the manual accompanying the DVD recorder.  
*8: Only the discs recorded in the video format and finalized can be played back.  
Unfinalized discs cannot be played back. Depending on the recording status of a disc, the disc may not be  
played back at all or normally (the picture or sound may not be smooth, etc.).  
*9: If there is too much recording space left on a disc (the used portion is less than 55mm across), it may not  
play back properly.  
*10: Do not glue paper or put stickers on to the disc. These may damage the disc and the unit may not read it correctly.  
*11: The number inside the symbol refers to a region of the world and a disc encoded in a specific region for-  
mat can only be played back on unit with the same region code.  
UNPLAYABLE DISCS  
¡
NEVER play back the following discs. Otherwise, malfunction may result!  
DVD-RAM / CD-I / Photo CD / Video CD / DVD with region codes other than 1 or ALL /  
DTS-CD / DVD-ROM for personal computers / CD-ROM for personal computers / MP3  
On the following disc, the sound MAY NOT be heard.  
¡
Super Audio CD  
NOTE: Only the sound recorded on the normal CD layer can be delivered.  
The sound recorded on the high density Super Audio CD layer cannot be delivered.  
Any other discs without compatibility indications  
¡
- 19 -  
EN  
 
PLAYING A DISC  
BASIC PLAYBACK  
GENERAL FEATURES  
DVD-V  
CD  
DVD-V  
DVD may contain menus to navigate the disc and  
Getting started  
access special features. Press the appropriate  
Number buttons or [K /L/s / B] to highlight your  
selection in the DVD main menu and hit [ENTER] to  
confirm.  
¡Turn on the power of amplifier and any other com-  
ponents, if necessary.  
1
Hit [POWER].  
¡The power will turn on.  
NOTES:  
¡Select DVD mode by hitting [SELECT], then  
2
3
Hit [OPEN/CLOSE A] to open disc loading  
tray.  
operate the DVD functions.  
¡Unless stated, all operations described are based on  
remote control use. Some operations can be carried  
out using the menu bar on the TV screen.  
Place the chosen disc in the tray, with the  
label facing up.  
DISC MENU  
DVD-V  
1
Hit [DISC MENU].  
¡The DVD main menu will appear.  
¡If the feature is not available,  
appear on the TV screen.  
¡If disc menu is available on the disc, audio language,  
subtitle options, chapters for the title and other  
options will appear for selection.  
symbol may  
4
Hit [PLAY O].  
¡The tray will close automatically and playback will  
then start from the first chapter or track of the disc.  
¡Closing the disc tray manually or by hitting  
[OPEN/CLOSE A] also starts playback.  
¡If the playback does not start automatically, hit  
[PLAY O].  
2
Press [K /L/s / B] to select an item and  
hit [ENTER] to confirm selection.  
¡When you playback a DVD which features a title  
menu, it may appear on the screen. In this case,  
refer to “TITLE MENU” on this page.  
TITLE MENU  
5
Hit [STOP C] to stop playback.  
DVD-V  
NOTES:  
1
Hit [TITLE].  
¡When the DVD mode has been switched to the TV  
mode, the DVD mode shuts down first and then the  
TV picture and sound appears in about 4 seconds.  
Similarly, when [POWER] is hit to turn off in the  
DVD mode, this mode shuts down first and then the  
unit is turned off.  
¡The title menu will appear.  
¡If the feature is not available,  
appear on the TV screen.  
symbol may  
2
Press [K /L/s / B] to select an item, and  
hit [ENTER] to confirm selection.  
¡A “prohibited icon” may appear  
at the top-right on the TV screen  
during operation, warning that a  
prohibited operation has been  
encountered by the DVD or the  
disc.  
¡With DVDs that use titles for playback program  
signals, playback may start from the second title or  
it may skip these titles.  
¡During the playback of a two layered disc, pictures  
may stop for a moment. This happens when the 1st  
layer switches to the 2nd layer. This is not a mal-  
function.  
CALLING UP A MENU SCREEN  
DURING PLAYBACK  
¡Hit [DISC MENU] to call up the DVD menu.  
¡Hit [TITLE] to call up the title menu.  
NOTE:  
¡Contents of menu and corresponding menu opera-  
tions may vary between discs. Refer to the manual  
accompanying the disc for details.  
- 20 -  
EN  
 
SLOW FORWARD /  
SLOW REVERSE  
RESUME  
DVD-V  
CD  
DVD-V  
1
During playback, hit [STOP C].  
¡Resume message will appear on the TV screen.  
1
2
During playback, hit [PAUSE F].  
D
E
] .  
Press [FWD  
] or [REV  
2
Hit [PLAY O], playback will resume from the  
point at which playback was stopped.  
¡“  
1” or “  
1” appears on the screen.  
3
To select another speed, repeat step 2 until  
your required speed number appears on the  
screen.  
¡To cancel resume, hit [STOP C] twice.  
¡The resume information stays on even when the  
power is turned off.  
¡Slow forward or reverse speed varies with the disc.  
Approximate speed is 1(1/16), 2(1/8) and 3(1/2).  
¡When you press buttons on the front panel, press  
PAUSE  
E
D
DVD-V  
CD  
and hold [SEARCH  
/
] for a few seconds.  
4
To return to normal playback, hit [PLAY O].  
1
During playback, hit [PAUSE F].  
¡Playback will pause and sound will be muted.  
2
To continue playback, hit [PLAY O].  
ZOOM  
DVD-V  
STEP BY STEP PLAYBACK  
The Zoom function allows you to enlarge the video  
image and to pan through the enlarged image.  
DVD-V  
1
Hit [ZOOM] during playback.  
¡Playback will continue.  
1
During playback, hit [PAUSE F].  
¡Playback will pause and sound will be muted.  
2
Hit [ZOOM] repeatedly to select the required  
zoom factor: ZOOM1, ZOOM2, ZOOM3 or  
OFF.  
2
3
The disc goes forward by one frame each  
time [PAUSE F] is hit.  
To exit step by step playback, hit [PLAY O].  
3
4
Press [K /L/s / B] to move the zoomed  
picture across the screen.  
FAST FORWARD /  
FAST REVERSE  
To exit zoom mode, hit [ZOOM] to OFF.  
NOTES:  
¡Zooming function does not work while disc menu is  
shown.  
DVD-V  
CD  
¡Zooming function is not available on some discs.  
¡It may take several seconds to slide the zoomed pic-  
ture.  
D
] or  
1
During playback, press [FWD  
E
].  
E
[REV  
D
¡“  
1” or “  
1” appears on the screen.  
¡The picture may be distorted if you operate other  
E
F
2
To select another speed, repeat step 1 until  
your required speed number appears on the  
screen.  
functions repeatedly (ex. [PAUSE ] or [REV  
],  
etc.) in the zoom mode.  
¡For DVDs, fast forward/reverse search speed is dif-  
ferent depending on the disc. Approximate speed is  
1(×2), 2(×8), 3(×20), 4(×50) and 5(×100).  
¡For Audio CDs approximate speed is 1(×2), 2(×8)  
and 3(×30).  
¡When you press buttons on the front panel, press and  
E
D
hold [SEARCH  
/
] for a few seconds.  
3
To return to normal playback, hit [PLAY O].  
- 21 -  
EN  
 
SEARCH FUNCTION  
TRACK SEARCH  
TIME SEARCH  
CD  
DVD-V  
CD  
There are three ways to begin playback on an Audio  
CD at a specific track.  
1
2
During playback, hit [SEARCH MODE] three  
times (CD: twice) to display the Time Search  
on the TV screen.  
Using the Number buttons  
Within 30 seconds, enter a desired disc  
time using the Number buttons.  
1
Press the Number buttons to enter the  
desired track number.  
¡Playback will start at the specified time.  
¡Hit [CLEAR] to erase the incorrect input.  
¡When there is no need to enter a number, “0”  
¡Playback will start at the selected track.  
¡For single digit tracks (1-9), press a single number  
(eg. track 3, hit [3]).  
appears automatically. For example, “ 0 : 0  
:
- - -  
¡To play track 26, hit [+10], [2], [6].  
appears in the Time Search display if the total time  
of the track or title is less than 10 minutes.  
Using [SEARCH MODE]  
1
Hit [SEARCH MODE].  
¡The track search display appears.  
MARKER SETUP SCREEN  
DVD-V  
CD  
2
Within 30 seconds, select the desired track  
number using the Number buttons.  
Use markers to memorize your favorite places on a  
disc.  
¡For single digits hit [0] first, if the total track of the  
disc is 10 tracks or more.  
1
Hit [SEARCH MODE] four times (CD: three  
times) during playback.  
¡Playback will start at the selected track.  
¡The display screen and Markers will appear on the  
TV screen.  
Using [SKIP H /  
G
]
During playback, hit [SKIP G] to move the next  
track. Hit it repeatedly to skip subsequent tracks. Hit  
[SKIP H ] to go back to beginning of the current  
track. Hit it repeatedly to go to the previous tracks.  
¡If [SKIP H / G] is pressed while the playback  
is paused, the playback will be paused again after  
skipping to the next track.  
2
3
Press [s / B] to select 1, 2, 3, 4, 5, 6, 7, 8, 9,  
or 10 and ensure that “  
appears in the display.  
:
:
- - - - - - - -  
When you reach the desired point, hit  
[ENTER].  
NOTE:  
¡The Title or Track and elapsed playing time will  
appear in the TV screen.  
¡[SKIP H / G] are not operative when playback  
is stopped.  
4
To return to the Marker later, hit [SEARCH  
MODE] four times (CD: three times) during  
playback and press [s / B] to choose the  
desired marker, then hit [ENTER].  
TITLE / CHAPTER SEARCH  
DVD-V  
NOTES:  
1
Hit [SEARCH MODE] once for the Chapter  
search, twice for the Title search during  
¡Operations which erase all Markers:  
– Opening the disc tray.  
playback.  
_/2  
– Turning off the power.  
– Hitting [SELECT].  
– Selecting “AC” at step 2 and hitting [ENTER].  
¡To clear a marker:  
2
Enter the desired chapter/title number using  
the Number buttons.  
– Press [s / B] to select a cursor on to the marker  
number and hit [CLEAR].  
¡You can mark up to 10 points.  
¡Playback will start at the selected chapter or title.  
¡Hit [CLEAR] to erase the incorrect input.  
¡For single digits hit [0] first, if the total number of  
chapter or title of the disc is 10 or more.  
5
Press [SEARCH MODE] or [RETURN] to  
exit.  
- 22 -  
EN  
 
SPECIAL PLAYBACK FUNCTION  
REPEAT  
PROGRAM  
CD  
You may determine the order in which tracks will play.  
REPEAT is available only during playback.  
REPEAT TITLE / CHAPTER  
DVD-V  
1
In the stop mode, hit [MODE].  
¡The “PROGRAM” screen will appear.  
To activate the repeat function, hit [REPEAT]  
during playback.  
¡The repeat mode changes as described below every  
time you hit the button.  
2
Press [K /L] to select a track, then hit  
[ENTER].  
¡Hit [CLEAR] to erase the  
most recently entered track.  
¡If the entire Program cannot be  
displayed at once on a screen,  
G” appears to go to the next  
page and H” appears to go  
back to the previous page.  
PROGRAM  
CD-DA  
TOTAL 1:03:30  
CHAPTER  
TITLE  
OFF  
(repeat off)  
1
5
3:30  
5:10  
1
3:30  
2
3
4
5
6
7
4:30  
5:00  
3:10  
5:10  
1:30  
2:30  
10 4:20  
11 3:00  
12 3:20  
17 4:10  
22 2:50  
2/3  
(current chapter repeat) (current title repeat)  
ENTER  
1/4  
PLAY  
1
3:30  
CLEAR  
NOTES:  
¡Repeat Title/Chapter is not available with some  
scenes.  
¡The REPEAT setting will be cleared when moving  
to other title or chapter.  
3
Repeat step 2 until you have selected all the  
tracks you want to play in the program.  
4
Hit [PLAY O] to play the programmed tracks.  
REPEAT TRACK  
NOTES:  
CD  
¡While the program is being played back, hitting  
[STOP C] works as follows.  
To activate the repeat function, hit [REPEAT]  
during playback.  
¡The repeat mode changes as described below every  
time you hit the button.  
¡Hit [STOP C] once and then [PLAY O] again,  
playback will restart from the point where  
[STOP C] was hit. (Program continued)  
¡Hit [STOP C] twice and then [PLAY O] again,  
playback will restart from the track in the usual  
way. (Program canceled)  
TRACK  
(current track repeat)  
ALL  
OFF  
(repeat off)  
(entire disc repeat)  
¡Up to 99 tracks can be entered.  
¡To erase all tracks in the program at once, select  
“ALL CLEAR” at the bottom of the list at step 2.  
¡If you like to repeat the current track in the program,  
NOTES:  
¡Repeat setting will be cleared when moving to other  
hit [REPEAT] several times until “  
TRACK”  
track.  
appears during playback. If you like to repeat the  
¡Repeat playback does not function during A-B  
repeat playback.  
entire program hit [REPEAT] several times until  
ALL” appears during playback.  
A-B REPEAT  
RANDOM PLAYBACK  
DVD-V CD  
CD  
1
¡“  
Hit [A-B] at your chosen starting point.  
A-” appears briefly on the TV screen.  
This function shuffles the playing order of tracks  
instead of playback in the sequence.  
2
Hit [A-B] again at your chosen end point.  
A-B” appears briefly on the TV screen, and the  
1
In the stop mode, hit [MODE] twice.  
¡“  
¡“RANDOM” screen appears.  
RANDOM  
repeat sequence begins.  
CD-DA  
TOTAL 0:45:55  
RANDOM PROGRAM  
no indication  
3
To exit the sequence, hit [A-B].  
NOTES:  
-
-
-
-
PLAY  
¡The A-B repeat section can only be set within the  
current title (for DVDs) or current track (for Audio  
CDs).  
¡A-B repeat is not available with some scenes in  
DVD.  
¡To cancel the A point which was set, hit [CLEAR].  
¡A-B repeat playback does not function during title,  
chapter, track or all repeat playback.  
2
Hit [PLAY O] to start random playback.  
NOTE:  
¡If you like to repeat the current track in the random  
selection, hit [REPEAT] several times until  
TRACK” appears during playback. If you like  
to repeat the entire random selection hit  
[REPEAT] several times until “ ALL” appears  
during playback  
.
- 23 -  
EN  
 
CHANGING THE SETTINGS  
SUBTITLE LANGUAGE  
STEREO SOUND MODE  
CD  
DVD-V  
The unit allows you to select a language for subtitles  
during DVD disc (if available) playback.  
1
Hit [AUDIO] repeatedly during playback to  
select between “STEREO”, “L-ch” or “R-ch”.  
STEREO  
1
Hit [SUBTITLE] during playback.  
¡The subtitle language will  
appear on the display bar at  
the top of the TV screen.  
1.ENG/6  
¡
STEREO - both right and left channels are active (stereo)  
L-ch - only left channel is active  
R-ch - only right channel is active  
2
3
Hit [SUBTITLE] repeatedly to select your  
desired subtitle language.  
CAMERA ANGLE  
DVD-V  
To turn off subtitles, hit [SUBTITLE] repeat-  
edly until “OFF” appears.  
Some DVD discs contain scenes which have been shot  
simultaneously from various angles. You can change  
NOTES:  
the camera angle when the “  
screen.  
” icon appears on the  
¡Hitting [SUBTITLE] may not work on some DVDs  
with multiple subtitle languages. In this case, set it  
on the disc menu. (Operation varies between discs.  
Refer to the manual of the disc.)  
1
Hit [ANGLE] during playback.  
¡The selected angle will be displayed on the display  
bar at the top of the screen.  
¡If the desired language is not shown after hitting  
[SUBTITLE] several times, the disc does not have  
subtitles in that language.  
1 / 8  
¡When “NOT AVAILABLE”  
appears on the TV screen, it  
means no subtitle is recorded  
on the scene.  
NOT AVAILABLE  
¡If the “ANGLE ICON” setting is “OFF” in the  
“OTHERS” menu, the “  
(Refer to page 28.)  
” icon will not appear.  
¡If you choose a language that has a 3 letter language  
code, the code will be displayed every time you  
change the Subtitle language setting. If you choose  
any other languages, “---” will be displayed instead.  
(Refer to page 26.)  
2
Hit [ANGLE] repeatedly to select your  
desired angle.  
BLACK LEVEL SETTING  
DVD-V  
Adjust the Black Level Settings to make the black  
parts of the picture brighter.  
AUDIO LANGUAGE  
1
Hit [MODE] during playback.  
DVD-V  
OFF  
The unit allows you to select a language during DVD  
disc (if multi languages are available) playback.  
1
Hit [AUDIO] during playback.  
2
Hit [ENTER] to switch “ON/OFF”.  
1.ENG Dolby D 3/2.1ch 48k/3  
ON: Makes the dark parts brighter.  
OFF: Shows the original picture as recorded.  
(Initial setting)  
2
Hit [AUDIO] repeatedly to select your  
desired language.  
3
Press [MODE] twice or [RETURN] to exit.  
NOTE:  
NOTE:  
¡The setting will be saved even if the unit is turned  
off.  
¡Hitting [AUDIO] may not work on some DVDs with  
multiple audio languages (e.g. DVDs which allow  
audio language setting on the disc menu).  
- 24 -  
EN  
 
VIRTUAL SURROUND  
DVD-V  
CD  
You can enjoy surround-sound effect over two speak-  
ers on this unit.  
1
Hit [MODE] twice (CD: once) during play-  
back.  
OFF  
2
3
Hit [ENTER] to set it “1” (Natural effect), “2”  
(Emphasized effect) or “OFF”.  
Hit [MODE] to exit.  
¡You can also exit the menu by hitting [RETURN].  
NOTE: (for CD play only)  
¡Virtual Surround will not be effective if the sound  
mode is set to something other than STEREO.  
THE ON-SCREEN INFORMATION  
DVD-V  
CD  
You can check the information about the current disc by hitting [DISPLAY].  
For DVD-Vs  
For Audio CDs  
1
Hit [DISPLAY] during playback to show cur-  
rent Chapter.  
1
Hit [DISPLAY] during playback to show the  
current Track.  
¡The elapsed and remaining  
playing time of the current  
chapter will be displayed.  
¡The elapsed and remaining playing time of the cur-  
9/49  
0:00:00 -0:03:30  
rent track will be displayed.  
4/12 0:03:21 - 0:02:15  
T
2
Hit [DISPLAY] again to show current Title.  
2
Hit [DISPLAY] again to show current Total  
Track.  
¡The elapsed and remaining  
playing time of the current title  
will be displayed.  
1/3 0:00:00 - 1:23:45  
¡The elapsed and remaining playing time of the total  
track will be displayed.  
4/12 0:13:45 - 0:45:40  
T
3
Hit [DISPLAY] again.  
¡The bit rate and the current  
repeat setting will be  
displayed.  
T
L1  
3
Hit [DISPLAY] again to exit.  
¡If you are playing a dual layered disc, the layer num-  
ber will also be displayed (L0: Layer 0 is playing.  
L1: Layer 1 is playing).  
NOTE:  
¡When you are playing a disc in PROGRAM or  
RANDOM mode, “ PROGRAM” (or RAN-  
DOM) will be displayed at step 2.  
4
Hit [DISPLAY] again to exit.  
PROGRAM  
B
- 25 -  
EN  
 
CHANGING THE DVD SET UP ITEMS  
Language  
Code Language  
Code  
CUSTOM MENU  
A-B  
L-N  
Abkhazian  
Afar  
Afrikaans  
Albanian  
Amharic  
Arabic  
Armenian  
Assamese  
Aymara  
Azerbaijani  
Bashkir  
Basque  
4748 Laothian  
4747 Latin  
4752 Latvian;Lettish  
6563 Lingala  
4759 Lithuanian  
4764 Macedonian  
5471 Malagasy  
4765 Malay  
5861  
5847  
5868  
5860  
5866  
5957  
5953  
5965  
5958  
5966  
5955  
5964  
5961  
5960  
6047  
6051  
6061  
DVD-V  
You can change the DVD player’s settings.  
1
Hit [SETUP] twice in the stop mode so that  
the DVD SETUP menu appears.  
4771 Malayalam  
4772 Maltese  
4847 Maori  
SETUP  
¡Hit [L] to select “CUSTOM”  
then hit [ENTER].  
QUICK  
CUSTOM  
INITIALIZE  
5167 Marathi  
Bengali;Bangla  
Bhutani  
Bihari  
4860 Moldavian  
5072 Mongolian  
4854 Nauru  
NOTE:  
¡If the menu does not appear, hit [PLAY O] first,  
then hit [STOP C]. Make sure the disc is in the stop  
mode, then slowly hit [SETUP] twice.  
Bislama  
Breton  
4855 Nepali  
4864 Norwegian [NOR]  
4853  
5971 Occitan  
4851 Oriya  
Oromo(Afan)  
5759 Panjabi  
4947 Pashto;Pushto  
7254 Persian  
4961 Polish  
5464 Portuguese [POR]  
4965 Quechua  
5047 Rhaeto-Romance  
6058 Romanian [RUM]  
5160 Russian [RUS]  
5161  
5166 Samoan  
Sangho  
5261 Sanskrit  
5256 Scots Gaelic  
5255 Serbian  
Bulgarian  
Burmese  
Byelorussian  
O-R  
6149  
6164  
6159  
6247  
6265  
5247  
6258  
6266  
6367  
6459  
6461  
6467  
2
Select the desired item.  
C-E  
K
L
¡Press [  
/
] to select the desired item then hit  
Cambodian  
Catalan  
[ENTER] to confirm.  
Chinese [CHI]  
Corsican  
Croatian  
Refer to the pages below to set up each item.  
SETUP  
CUSTOM  
A
P 26 Step  
3
3
3
3
3
Czech  
Danish [DAN]  
Dutch [DUT]  
English [ENG]  
Esperanto  
Estonian  
LANGUAGE  
DISPLAY  
AUDIO  
PARENTAL  
OTHERS  
B
P 27 Step  
C
P 27 Step  
S
D
P 28 Step  
6559  
6553  
6547  
5350  
6564  
6554  
6566  
6660  
6560  
6550  
6555  
6565  
6557  
6558  
6561  
5165  
6567  
6569  
6568  
E
F-H  
P 28 Step  
Faroese  
Fiji  
A
LANGUAGE SETTING  
Follow steps to in the “CUSTOM MENU” section  
Finnish [FIN]  
French [FRE]  
Frisian  
5264 Serbo-Croatian  
5271 Sesotho  
5358 Setswana  
5747 Shona  
1
2
above.  
Galician  
Georgian  
German [GER]  
Greek [GRE]  
Greenlandic  
Guarani  
K
L
3
Press [  
hit [ENTER].  
/
] to select the desired item then  
5051 Sindhi  
5158 Singhalese  
5758 Siswat  
5360 Slovak  
SETUP  
LANGUAGE  
AUDIO:  
Sets the audio language.  
AUDIO  
SUBTITLE  
DISC MENU  
ORIGINAL  
Gujarati  
Hausa  
Hebrew  
5367 Slovenian  
5447 Somali  
5569 Spanish [SPA]  
5455 Sundanese  
5467 Swahili  
OFF  
SUBTITLE:  
ENGLISH  
Sets the subtitle language.  
DISC MENU:  
Hindi  
Hungarian [HUN]  
I-K  
Icelandic [ICE]  
Indonesian  
Interlingua  
Interlingue  
Inupiak  
Irish [IRI]  
Italian [ITA]  
Japanese [JPN]  
Javanese  
Kannada  
Kashmiri  
Swedish [SWE]  
Sets the language for DVD menu.  
5565  
5560 Tagalog  
5547 Tajik  
5551 Tamil  
5557 Tatar  
5347 Telugu  
5566 Thai  
T
6658  
6653  
6647  
6666  
6651  
6654  
4861  
6655  
6661  
6665  
6664  
6657  
6669  
K
L
] to select a setting then hit  
4
Press [  
[ENTER].  
/
SETUP  
LANGUAGE  
LANGUAGE  
LANGUAGE  
¡If “OTHER” is selected on  
the “AUDIO”, “SUBTITLE”  
or “DISC MENU” screen,  
press four-digit number to  
enter the code for the  
desired language. (Refer to  
the language code list.)  
¡Only the languages support-  
ed by the disc can be select-  
ed.  
AUDIO  
ORIGINAL  
ENGLISH  
FRENCH  
5647 Tibetan  
5669 Tigrinya  
5760 Tonga  
5765 Tsonga  
5757 Turkish [TUR]  
6469 Turkmen  
5771 Twi  
SETUP  
SUBTITLE  
OFF  
ENGLISH  
FRENCH  
Kazakh  
Kinyarwanda  
Kirghiz  
Kirundi  
Korean [KOR]  
Kurdish  
6460  
U-Z  
5761 Ukrainian  
5767 Urdu  
Uzbek  
6757  
6764  
6772  
6855  
6861  
4971  
6961  
7054  
5655  
7161  
7267  
SETUP  
DISC MENU  
ENGLISH  
FRENCH  
Vietnamese  
Volapuk  
Welsh  
SPANISH  
Wolof  
Xhosa  
Yiddish  
5
Hit [SETUP] to exit the menu.  
NOTES:  
Yoruba  
Zulu  
¡Language Setting for Audio and Subtitle are not  
valid for some discs due to default setting of the  
disc. In this case, set them by hitting [AUDIO] and  
[SUBTITLE]. (Refer to page 24.)  
¡If you select a language that is not supported by the  
disc, subtitle will automatically be set OFF and the  
first item of the audio languages will be automatical-  
ly set.  
If you choose a language that has a 3 letter language  
code, the code will be displayed every time you change  
the AUDIO or SUBTITLE language setting above. If  
you choose any other languages, ‘---’ will be displayed  
instead. (3 letter language code is written in bracket.)  
- 26 -  
EN  
 
B
C
DISPLAY SETTING  
AUDIO SETTING  
Choose the appropriate Audio settings for your equip-  
ment as it only affects during the playback of DVD  
discs.  
Follow steps to in the “CUSTOM MENU” section  
on page 26.  
1
2
K
L
3
Press [  
/
] to select the below items then  
Follow steps to in the “CUSTOM MENU” section  
on page 26.  
1
2
hit [ENTER].  
TV MODE:  
QUICK  
K
L
3
Press [  
/
] to select the below items then  
You can change certain aspects of the DVD display  
screens and on-screen messages on the TV screen.  
hit [ENTER].  
DRC (Dynamic Range  
Control):  
¡To compress the range of soft  
to loud sound.  
¡4:3 LETTER BOX (default):  
To show black bars on top  
and bottom of the screen.  
SETUP  
DISPLAY  
SETUP  
DRC  
DOWN SAMPLING  
DOLBY DIGITAL  
AUDIO  
ON  
ON  
BITSTREAM  
TV MODE  
STILL MODE  
4:3 LETTER BOX  
AUTO  
¡4:3 PAN & SCAN: To show  
a full height picture with both sides trimmed.  
¡The default setting is “ON”.  
DOWN SAMPLING:  
¡ON : Output in 48 kHz.  
(default)  
¡OFF : Output the original  
sound.  
When playing disc with copyright Protection  
¡If you select “OFF”, copyright protection will be  
activated and sound will be down sampled at 48kHz.  
SETUP  
AUDIO  
DRC  
DOWN SAMPLING  
DOLBY DIGITAL  
ON  
ON  
BITSTREAM  
STILL MODE  
This function allows you to adjust picture resolution  
and quality in the still mode.  
:
SETUP  
DISPLAY  
¡AUTO (default):  
Automatically select the best  
resolution setting (FRAME  
or FIELD) based on the data  
characteristics of the pictures.  
¡FIELD: Select “FIELD” when the pictures are still  
unstable even if “AUTO” is selected.  
FIELD stabilizes the pictures, although the picture  
quality may become coarse due to the limited  
amount of data.  
¡FRAME: Select “FRAME” to display relatively  
motionless pictures in higher resolution.  
FRAME improves the picture quality, although it  
may unstabilizethe pictures due to simultaneous  
output of two field data.  
TV MODE  
STILL MODE  
4:3 LETTER BOX  
AUTO  
SETUP  
DRC  
DOWN SAMPLING  
DOLBY DIGITAL  
AUDIO  
DOLBY DIGITAL:  
QUICK  
ON  
ON  
BITSTREAM  
Set to “BITSTREAM” when  
the unit is connected to a  
Dolby Digital Decoder.  
¡BITSTREAM: Output a Dolby Digital signal  
(default)  
¡PCM: Convert the Dolby Digital to PCM  
(2 channel stereo)  
4
Hit [SETUP] to exit the menu.  
4
Hit [SETUP] to exit the menu.  
QUICK MENU  
¡You can select the “TV MODE” or “DOLBY DIGITAL” from the QUICK menu quickly. To access the  
QUICK menu, select “QUICK” instead of “CUSTOM” at step on page 26.  
1
LANGUAGE SETTING FOR THE ON-SCREEN MENUS  
¡You can access the TV SETUP menu by hitting [SETUP] from the DVD mode. Refer to  
“MENU LANGUAGE” on page 17 to change the language for the on-screen menus.  
- 27 -  
EN  
 
D
PARENTAL CONTROL  
IF YOU FORGET THE PASSWORD  
Parental Control limits the disc viewing that exceed  
your setting (with a password or playback will stop).  
This feature allows you to prevent discs with alterna-  
tive scenes from being played by your children.  
1
Hit the Number buttons [4], [7], [3], [7] at  
step 3. Then enter your new password.  
¡Password will be cleared and parental level will be  
set to “ALL”.  
PARENTAL LEVEL  
Parental Level allows you to set the rating level of  
your DVD discs. Playback will stop if the disc’s rat-  
ings exceed the level you set.  
2
Proceed with steps 4 to 6 again.  
E
OTHER SETTINGS  
Follow steps 1 to 2 in the “CUSTOM MENU” section  
on page 26.  
Follow steps to in the “CUSTOM MENU” section  
1
2
on page 26.  
3
Enter your four-digit password then hit  
[ENTER].  
K
L
3
Press [  
/
] to select the below items, then  
SETUP  
PARENTAL  
PASSWORD  
Enter current password.  
hit [ENTER].  
SETUP  
OTHERS  
ANGLE ICON  
ON  
AUTO POWER OFF ON  
ANGLE ICON:  
¡Hit [ENTER] repeatedly to turn Angle icon “ON” or  
“OFF”.  
K
L
] to select “PARENTAL LEVEL”  
4
5
Press [  
/
SETUP  
PARENTAL  
then hit [ENTER].  
PARENTAL LEVEL  
PASSWORD CHANGE  
ALL  
¡The default setting is “ON”.  
AUTO POWER OFF:  
¡Hit [ENTER] repeatedly to turn Auto Power off  
K
L
] to select the desired level then  
Press [  
/
“ON” or “OFF”.  
hit [ENTER].  
SETUP  
PARENTAL  
PARENTAL LEVEL  
¡
The default setting is “ON” and the screen saver pro-  
gram starts when there is no input from the unit for 5  
minutes in the stop mode. After the screen saver pro-  
gram is activated for 15 minutes, the power is auto-  
matically turned off.  
ALL  
8
7 [NC-17]  
6 [R]  
6
Hit [SETUP] to exit the menu.  
NOTES:  
4
Hit [SETUP] to exit the menu.  
¡
When doing this for the first time, enter any 4 digits.  
(except for 4737) That number will be used as the pass-  
word. (in the event you forget the password, see below)  
K
L
¡To change the password, press [  
/
] to select  
INITIALIZE  
PASSWORD CHANGE” at step 4 then hit  
[ENTER]. Enter the four-digit password, then hit  
[ENTER].  
DVD-V  
This allows you to return all selections of SETUP  
(except for “PARENTAL” and menu language) to  
their default settings.  
¡With some DVDs, it may be difficult to find if they  
are compatible with parental lock. Be sure to check  
if the parental lock function operates in the way that  
you have set.  
1
Hit [SETUP] twice in the stop mode so that  
the “INITIALIZE” menu appears.  
¡Record the password in case you forget it.  
K
L
CONTROL LEVELS  
2
Press [  
/
] to select “INITIALIZE” then hit  
¡
ALL  
SETUP  
[ENTER].  
QUICK  
CUSTOM  
INITIALIZE  
All parental lock is cancelled.  
¡
Level 8  
DVD software of any grade (adult/general/children)  
can be played back.  
K
L
3
Press [  
/
] to select “YES” then hit  
[ENTER] twice.  
¡
Levels 7 to 2  
All the settings (except for  
PARENTAL” and menu  
language) will be cleared.  
¡To cancel the initialization,  
select “NO”.  
Only DVD software intended for general use and  
children can be played back.  
SETUP  
INITIALIZE  
Initialize?  
NO  
YES  
¡
Level 1  
Only DVD software intended for children can be  
played back, with those intended for adult and gen-  
eral use prohibited.  
4
Hit [SETUP] to exit the menu.  
- 28 -  
EN  
 
TROUBLESHOOTING GUIDE  
If the unit does not perform properly when operated as instructed in this Owner’s Manual, check the unit, con-  
sulting the following checklist.  
PROBLEM  
CORRECTIVE ACTION  
Make sure the power plug is connected to an AC outlet.  
Make sure the power is turned on.  
Check if the power plug is connected to an AC outlet.  
Check the batteries in the remote control.  
Aim the remote control directly at the remote sensor. If necessary,  
remove all the obstacles between the sensor and the remote control.  
You have to be within 23 feet of the unit.  
No power  
No operation by infrared remote  
control  
Check if the correct mode is selected. If not switch the mode by  
hitting [SELECT], whichever you need.  
TV Mode  
Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked  
possibilities. Before arranging for service, check these items. It could save your time and money.  
PROBLEM  
No picture or sound  
CORRECTIVE ACTION  
Make sure the AC cord is connected to an AC outlet.  
Check antenna connection.  
Hit [SELECT] to select TV mode.  
Then try other TV feature.  
Let the unit program its tuner memory.  
Adjust direction or replace antenna.  
Adjust picture controls.  
Check for broken pin of the antenna cable.  
Adjust volume control on remote control or main unit.  
Hit [MUTE] to restore sound.  
No picture or poor picture on the  
unit  
No sound or poor sound  
Bars On Screen  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Picture Distorted or Blurred  
Try a new channel, if OK, then possible station trouble.  
If outside antenna is being used, check for broken wire.  
Try a new channel, if OK, then possible station trouble.  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to jack on the back of the set?  
If outside antenna is being used, check for broken wire.  
Adjust “COLOR” control.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to jack on the back of the set?  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to jack on the back of the set?  
If outside antenna is being used, check for broken wire.  
Adjust “CONTRAST” & “BRIGHT” control.  
Try a new channel, if OK, then possible station trouble.  
Is antenna connected to jack on the back of the set?  
If outside antenna is being used, check for broken wire.  
Check for local interference.  
Picture Rolls Vertically  
Lines or Streaks in Picture  
No Color  
Poor Reception on Some Channels  
Ghosts in Picture  
Weak Picture  
Sound OK, Picture Poor  
Adjust “CONTRAST” & “BRIGHT” control.  
- 29 -  
EN  
 
PROBLEM  
Picture OK, Sound Poor  
CORRECTIVE ACTION  
Try a new channel, if OK, then possible station trouble.  
Check for local interference.  
Make sure the AC cord is connected to an AC outlet.  
Check batteries in remote control.  
Magnetism from nearby appliances and geomagnetism might affect  
the color of the TV picture. Move the unit away from the appliances,  
the unit can repair itself automatically. If you want to repair immedi-  
ately, unplug the power cord, then plug it in again 30 minutes later or  
so. This automatically resets the unit.  
No operation by infrared remote  
control  
Different color marks on screen  
CLOSED CAPTION PROBLEM  
POSSIBLE REMEDY  
Misspelling in captions  
Error committed by the closed captioning production company.  
Possible in a live broadcast. Not in case of a prerecorded program.  
A few seconds of delay is common for live broadcast.  
Display capacity may not exceed 220 words per minute. If a dialogue  
exceeds that rate, selective editing is used to insure that the captions  
remain up-to-date with the current TV screen dialogue.  
Text is not shown in its entirety or  
a delay occurs from what is being  
said  
Captions scrambled with white  
boxes  
Caused by interferences of building, power lines, thunderstorms, etc.  
No captions in a program which  
must contain closed caption  
The broadcast may use a time compression process to speed up the  
program. The decoder cannot read the compressed information and  
captions will be lost.  
You are in TEXT mode. Select a CAPTION mode (“C1”, “C2”) or  
Caption “OFF”.  
Black box in the TV screen  
- 30 -  
EN  
 
DVD Mode  
PROBLEM  
CORRECTIVE ACTION  
Insert a correct video disc that plays on this unit.  
Hit [SELECT] to select DVD mode, then try other DVD feature.  
Insert the disc.  
No picture  
Disc cannot be played  
Clean the disc.  
Place the disc correctly, with the label side up.  
Cancel the parental lock or change the control level.  
Connect the audio cables firmly.  
No sound  
Turn the power of the audio component on.  
Correct the audio output settings.  
Correct the input settings on the audio component.  
This unit does not support DTS audio. This is not a malfunction.  
No DTS audio is output  
Distorted picture  
There are some cases where pictures may be slightly distorted,  
which are not a sign of a malfunction.  
Although pictures may stop for a moment, this is not a malfunction.  
The selected language is not available for audio or subtitles on the  
DVD. (This is not a malfunction.)  
Audio or subtitle language  
does not match the set up  
The camera angle cannot be changed The DVD does not contain sequences recorded from different cam-  
era angles. (This is not a malfunction.)  
Audio or subtitle language cannot be The DVD does not contain audio source or subtitles in the selected  
changed  
language. (This is not a malfunction.)  
“Prohibited icon” appears on the  
screen, prohibiting an operation  
CD sound dropout  
That operation is prohibited by the unit or the disc.  
(This is not a malfunction.)  
Scratched disc. Replace the disc with an unscratched one.  
No CD reproduction  
DVD picture dropout  
DVD picture freeze  
DVD picture in mosaic  
No DVD reproduction  
NOTES:  
Some functions are not available in specific modes, but this is not a malfunction. Read the description in  
this Owner’s Manual for details on correct operations.  
Playback from a desired track and random playback are not available during program playback.  
- 31 -  
EN  
 
MAINTENANCE  
CABINET CLEANING  
SERVICING  
Should your unit become inoperative, do not try to  
Wipe the front panel and other exterior surfaces of  
the unit with a soft cloth immersed in lukewarm  
water and wrung dry.  
correct the problem by yourself. There are no user-  
serviceable parts inside. Turn off, unplug the power  
cord and please call our help line mentioned on  
the front page, to locate an Authorized Service  
Center.  
Never use a solvent or alcohol. Do not spray insec-  
ticide liquid near the unit. Such chemicals may  
cause damage and discoloration to the exposed sur-  
faces.  
IF THE LASER OPTICAL PICKUP UNIT IS DIRTY  
If the unit still does not perform properly when it is operated, while referring to the relevant sections and to  
“TROUBLESHOOTING GUIDE” in this Owner’s Manual, the laser optical pickup unit may be dirty.  
Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup  
unit.  
DISC HANDLING  
Handle the discs so that fingerprints and dust do  
not adhere to the surfaces of the discs.  
To clean-off, use a soft cloth.  
Do not use a hard cloth since this will mar the disc.  
Wipe the disc in a straight line from center to edge.  
Never wipe with a circular motion.  
Do not use detergent or abrasive cleaning agents.  
Always store the disc in its protective case when it  
is not used.  
- 32 -  
EN  
 
SPECIFICATIONS  
GENERAL SPECIFICATIONS  
ELECTRICAL SPECIFICATIONS  
Sound output:  
2 speakers, 1W, 8 ohm  
TV  
CRT:  
20 inch in-line gun,  
90˚ deflection tube  
NTSC-M  
OTHER SPECIFICATIONS  
Terminals  
Antenna input:  
Television system:  
Closed caption system: §15.119/FCC  
Channel coverage:  
VHF:  
UHF:  
CATV:  
VHF/UHF/CATV  
75 ohm unbalanced (F-type)  
RCA connector [ 1  
RCA connector [ 2  
Video input:  
Audio L/R input:  
Headphone:  
2 ~ 13  
14 ~ 69  
1/8" stereo (3.5 mm)  
2 ~13, A ~ W,  
W+1 ~ W+84,  
A-5 ~ A-1, 5A  
181 channel  
frequency synthesized  
tuning system  
Direct access keyboard,  
programmable  
scan and up/down  
Coaxial digital  
audio output:  
One pin jack,  
500m Vpp (75 ohm)  
Digital encoded  
Tuning System:  
Channel access:  
Remote control:  
infrared light system  
Operating  
temperature:  
5°C to 40°C  
(41°F~104°F)  
Power requirements: AC 120V, 60Hz  
Power consumption  
(Maximum):  
Picture tube:  
Dimensions:  
80W  
20" PF  
H : 20-1/4" (514mm)  
W : 20-3/16" (512mm)  
D : 19-13/16" (503mm)  
46.3 lbs. (21.0kg)  
DVD  
Product type:  
Discs:  
Output signal format: NTSC color  
DVD Player  
DVD video, Audio CD  
Weight:  
Designs and specifications are subject to change without notice.  
If there is a discrepancy between languages, the default language will be English.  
- 33 -  
EN  
 
INDICE  
INDICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
SECCIÓN DE TV  
CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 34  
PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 35  
CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 35  
CONEXIÓN A TOMAS DE ENTRADA DELANTERAS 36  
CONEXIÓN A UN AMPLIFICADOR ESTÉREO  
PARA MIRAR UN PROGRAMA DE TV . . . . . . . . . . . . 37  
IDIOMA DEL MENÚ . . . . . . . . . . . . . . . . . . . . . . . . . . . 37  
SECCIÓN DE DVD  
REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . . . . . . 38  
MENÚ DE DISCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
REANUDACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
EQUIPADO CON TOMAS DE ENTRADA DIGITAL  
(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
CONEXIÓN A UN DECODIFICADOR DOLBY DIGITAL  
(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 36  
CONTROLES DE OPERACIÓN Y FUNCIONES  
• Consulte la figura 1 de la página 8 para el panel frontal de la unidad  
• Consulte la figura 2 de la página 8 para el mando a distancia  
• Consulte la figura 3 de la página 9 para la vista posterior  
1. Bandeja de carga del disco  
2. Toma de entrada VIDEO  
Conecte aquí la toma de salida de vídeo de una  
videocámara o de una videograbadora.  
Botón +100  
Presione para seleccionar canales de televisión por  
cable cuyo número sea superior a 99.  
Modo DVD:  
Presione para introducir el número deseado.  
Botón +10  
Presione para introducir números superiors a 9.  
3. Tomas de entrada AUDIO L/R  
Conecte aquí las tomas de salida de audio de una  
videocámara o de una videograbadora.  
16. Botón SLEEP  
4. Botón POWER  
Presione para encender y apagar la unidad.  
Utilise para ajustar el temporizador de dormir.  
17. Botón DISPLAY  
K
L
5. Botones VOLUME (VOL.)  
/
Modo TV:  
Presione para controlar el nivel de volumen del DVD y  
el televisor.  
Indica el número del canal en la pantalla del televisor.  
Modo DVD:  
Indica el estado actual en la pantalla del televisor.  
K
L
6. Botones CHANNEL (CH.)  
/
Utilice para seleccionar canales memorizados.  
7. Ventanilla del sensor de mando a distancia  
8. Botón STOP  
Detiene la operación del disco.  
9. Botones SKIP H /  
Presione una vez para omitir capítulos o pistas y  
desplazarse a un punto específico.  
18. Botón SETUP  
Presione para entrar o salir del menú de configuración  
de televisor o DVD.  
C
19. Botón TITLE  
G
Para visualizar el menú de títulos.  
20. Botón CLEAR  
Para cancelar o borrar un ajuste entrado actualmente.  
E
D
Botones SEARCH  
/
(Panel frontal)  
21. Botón MODE  
Mantenga el botón presionado para cambiar la  
velocidad de reproducción en avance o retroceso.  
Presione para llamar la pantalla de la reproducción  
programada o la de reproducción aleatoria en el modo  
de parada.  
10. Botón PLAY  
Inicia la reproducción del contenido del disco.  
11. Botón PAUSE  
Hace una pausa en la reproducción del disco.  
12. Botón OPEN/CLOSE  
B
Presione para llamar la pantalla de ajuste del nivel del  
negro o la pantalla de sonido ambiental durante la  
reproducción.  
F
A
22. Botón SEARCH MODE  
Presione para insertar un disco en la bandeja o retirarlo  
de ella.  
Presione para localizar un punto deseado.  
23. Botón AUDIO  
13. Toma HEADPHONE  
Presione para seleccionar un modo de sonido o idioma  
de audio deseado.  
Para conectar auriculares (no suministrados) y escuchar  
en privado.  
24. Botón SUBTITLE  
14. Botón PICTURE  
Presione para seleccionar el idioma de subtítulos  
deseado.  
Presione para ajustar la imagen.  
15. Botones Numéricos  
25. Botón REPEAT  
Modo TV:  
Repite la reproducción del disco, título, capítulo o pista  
actual.  
Presione dos cifras para acceder directamente al canal  
deseado.  
26. Botón ANGLE  
No olvide presionar [0] antes de elegir un canal de una  
Presione para cambiar el ángulo de la cámara y ver la  
secuencia que se está reproduciendo desde un ángulo  
diferente (si existe).  
sola cifra.  
- 34 -  
ES  
 
33. Botón ZOOM  
27. Botón A-B  
Amplía parte de la imagen reproducida de un DVD.  
Repite la reproducción de una sección seleccionada.  
34. Botón MUTE  
28. Botón RETURN  
Suprime la salida de sonido. Presiónelo de nuevo para  
restablecer el sonido.  
Permite volver a la pantalla anterior en el menú de  
configuración.  
35. Botón SELECT  
29. Botón ENTER  
Presione para cambiar al modo TV, modo de entrada  
externa o modo de DVD.  
Presione para establecer un ajuste.  
K
L
{
B
30. Botones  
Modo TV:  
/
/
/
36. Toma COAXIAL  
Conecte solamente a la entrada digital de un  
amplificador externo o decodificador (para audio de  
DVD solamente).  
Presione para seleccionar un modo de ajuste en el  
menú que aparece en la pantalla del televisor.  
Presiónelos también para seleccionar opciones o  
establecer ajustes en un menú en particular.  
Modo DVD:  
37. Toma ANT.  
Conecte a una antena, sistema de televisión por cable o  
sistema de satélite.  
Presione para hacer una selección en el menú.  
31. Botón DISC MENU  
38. Cable eléctrico  
Muestra menú del DVD.  
Conécte a un toma de CA estándar (120 V/60 Hz).  
NOTA:  
E
32. Botón REV  
Antes de conectar el cable eléctrico a una toma de  
Presione para mover la imagen de DVD en retroceso  
rápido en o en cámara lenta en retroceso.  
CA, retírelo del gancho para evitar dañarlo.  
D
Botón FWD  
Presione para mover en avance rápido o en cámara  
lenta en el disco.  
PREPARACIÓN PARA LA UTILIZACIÓN  
NOTA:  
CONEXIONES DE ANTENA/CABLE  
Antes de enchufar la antena a la toma ANT. de la  
unidad, compruebe que la clavija no esté doblada.  
Si esta doblada, póngala derecha como se muestra  
en la ilustración, y luego conéctela en la toma  
ANT. de la unidad.  
Consulte la figura 4 de la página 10  
Nota para el instalador de sistemas CATV  
Esta nota tiene la finalidad de llamar la atención  
del instalador de sistemas CATV para que tenga  
en cuenta el Artículo 820-40 de la NEC, que  
proporciona recomendaciones para hacer una  
conexión a tierra apropiada y, en particular,  
especifica que la tierra del cable debe conectarse  
al sistema de puesta a tierra del edificio, tan cerca  
del punto de entrada del cable como sea posible.  
Clavija doblada  
Cable  
Clavija  
(Necesita enderezarse)  
(Clavija derecha)  
NOTA:  
Para su seguridad y para evitar que se dañe  
la unidad, desenchufe el cable de antena de la  
toma ANT. antes de mover la unidad.  
- 35 -  
ES  
 
CONEXIÓN A TOMAS DE  
ENTRADA DELANTERAS  
Cuando vea un programa grabado en otra fuente  
(videograbadora o videocámara), utilice las tomas de  
entrada AUDIO/VIDEO de la parte delantera de la  
unidad.  
Conecte las tomas de salida de audio/vídeo de otra  
fuente a las tomas AUDIO L/R y VIDEO de esta  
unidad.  
CONEXIÓN A UN  
DECODIFICADOR DOLBY  
DIGITAL (para DVD)  
Si utiliza esta unidad para reproducir un disco DVD  
en un formato de sonido envolvente Dolby Digital de  
5,1 canales, la unidad dará salida a un flujo de datos  
DOLBY DIGITAL desde su toma COAXIAL. Si  
conecta la unidad a un decodificador Dolby Digital,  
podrá disfrutar de una tonalidad más convincente y  
real, con un sonido envolvente potente y de alta  
calidad similar al de los cines.  
K
L
] hasta  
Despúes, presione [SELECT] o [CH.  
que aparezca “AUX” en la pantalla.  
/
Utilice cables digitales coaxiales de audio  
(disponibles en el comercio) para hacer las  
conexiones de audio.  
Consulte la figura 5 de la página 11  
NOTA:  
Cuando conecte una videograbadora monofónica  
(otra fuente) a esta unidad, conecte la toma de  
salida de audio de la videograbadora monofónica  
(otra fuente) a la toma AUDIO L de esta unidad. El  
audio saldrá igualmente por los canales izquierdo y  
derecho.  
Consulte la figura 7 de la página 12  
NOTAS:  
Asegúrese de apagar todos los componentes del  
sistema antes de conectar otro componente.  
Consulte los manuales de instrucciones de los  
componentes que va a conectar a la unidad.  
Si conecta un decodificador Dolby Digital, ajuste  
CONEXIÓN A UN AMPLIFICADOR  
ESTÉREO EQUIPADO CON TOMAS  
DE ENTRADA DIGITAL (para DVD) •  
la función “DOLBY DIGITAL” a “BITSTREAM”  
para salida de audio en el modo de configuración.  
A menos que se haga la conexión a un  
decodificador Dolby Digital, ajuste la función  
“DOLBY DIGITAL” a “PCM” para salida de  
audio en el modo de configuración. La  
Utilice un cable digital coaxial de audio (disponible en  
el comercio) para hacer las conexiones de audio.  
Conexión a un amplificador equipado con tomas de  
entrada digital, platina MD o platina DAT.  
reproducción en una unidad utilizando ajustes  
incorrectos puede generar ruido y distorsión, y  
también puede provocar daños a los altavoces.  
Consulte la figura 6 de la página 11  
NOTAS:  
La fuente de audio de un disco grabado en formato  
de sonido envolvente Dolby Digital de 5,1 canales  
no se puede grabar como sonido digital mediante  
Fabricado bajo licencia de Dolby  
Laboratories. “Dolby” y el símbolo de la  
doble D son marcas comerciales de Dolby  
Laboratories.  
uAnsaegpúlaretisneadMe DapoagDarAtTo.dos los componentes del  
sCisotnesmulateanlotessmdaencuoanleesctdaer ointrsotrucoccmiopnoensendtee.los  
PARA INSERTAR LAS PILAS  
Acojmuspteonlaenftuenscqióune vDa Oa LcoBnYecDtaIrGaITlaAuLnidaadP. CM”  
para salida de audio en el modo de configuración.  
La reproducción en una unidad utilizando ajustes  
incorrectos puede generar ruido y distorsión, y  
también puede provocar daños a los altavoces.  
1) Abra la cubierta del compartimiento de las pilas  
empujando la cubierta del mando a  
distancia en el sentido de la flecha.  
2) Inserte 2 pilas “AA” en el  
compartimiento de las pilas, en el  
sentido indicado por las marcas de polaridad (+/-).  
3) Vuelva a poner la cubierta.  
- 36 -  
ES  
 
SECCIÓN DE TV  
PARA MIRAR UN  
IDIOMA DEL MENÚ  
PROGRAMA DE TV  
TV  
TV  
1 Seleccione “LANGUAGE”  
Presione [SETUP].  
1 Enchufe el cable eléctrico  
Enchufe el cable eléctrico de la unidad en un  
tomacorriente de CA del hogar.  
NOTA:  
K
L
Presione [  
/
] para apuntar a “LANGUAGE”.  
2 Seleccione “ENGLISH”, “ESPAÑOL” o  
Si aparecen números en la esquina de la pantalla,  
“FRANÇAIS”  
presione [POWER] sin desenchufar el cable  
Presione [ENTER] repetidamente para seleccionar  
“ENGLISH” = inglés, “ESPAÑOL” o  
“FRANÇAIS” = francés.  
eléctrico.  
2 Encienda la unidad  
Presione [POWER] para encender la unidad.  
3 Salga del modo de idioma  
Presione [SETUP] para salir del menú.  
NOTAS:  
3 Seleccione el número de canal  
K
L
Presione [CH.  
/
] o los botones numéricos para  
seleccionar su número de canal deseado.  
Esta función afecta sólo el idioma en el menú de la  
pantalla y no la fuente de audio.  
Nota para el uso de los botones numéricos:  
¡Debe colocar un cero antes de los números de canal  
de una sola cifra (por ejemplo: 02, 03, 04, etc.).  
Si por alguna razón, el menú está en francés,  
presione [SETUP], presione [  
K
L
/
] para apuntar  
¡
Cuando seleccione canales de cable de más de 99,  
presione primero [+100] y después las dos últimas  
cifras. (Ejemplo: para seleccionar el canal 125,  
primero presione [+100] y después presione [2] y [5].)  
al “LANGAGE [FRANÇAIS]” y presione  
[ENTER] repetidamente para seleccionar el  
idioma deseado y presione [SETUP].  
4 Ajuste el sonido  
X
Y
Presione [VOL.  
/
] para ajustar el volumen.  
Presione [MUTE] para silenciar instantáneamente el  
sonido.  
Presione nuevamente para recuperar el nivel de  
sonido anterior.  
NOTA:  
K
L
Si presione [CH.  
/
] en el modo DVD, puede  
cambiar los canales de TV. Incluso si apaga la  
unidad en el modo DVD, cuando vuelva a  
encender, volverá al modo TV.  
PARA VER CANALES DE CABLE O  
SATELITE  
Si la unidad está conectada a una caja de cable o  
K
L
] para  
caja de satélite, presione [CH.  
/
seleccionar CH3 o CH4 de acuerdo con el ajuste  
de canal de salida del dispositivo y seleccione el  
canal deseado en el dispositivo.  
PARA VER UNA ENTRADA EXTERNA  
Cuando se conecta un equipo externo en las tomas  
de entrada AUDIO/VIDEO frontales, presione  
K
L
[SELECT] o [CH.  
/
] repetidamente hasta que  
aparezca “AUX” en la pantalla.  
- 37 -  
ES  
 
SECCIÓN DE DVD  
REPRODUCCIÓN BÁSICA  
MENÚ DE DISCO  
DVD-V  
CD  
DVD-V  
Para empezar  
1
Presione [DISC MENU].  
¡Conecte la alimentación del amplificador y otros ¡Aparecerá el menú principal de DVD.  
componentes, si es necesario.  
¡Si no existe la función, puede aparecer el símbolo  
en la pantalla de TV.  
1
Presione [POWER].  
¡La alimentación se conectará.  
¡Si el menú de disco existe en el disco, aparecerán el  
idioma de audio, opciones de subtítulo, capítulos  
para el título y otras opciones para su selección.  
2
3
Presione [OPEN/CLOSE A] para abrir la  
bandeja de carga del disco.  
K
L
{
B
2
Presione [  
/
/
/
] para hacer una  
Ponga el disco deseado en la bandeja, con  
la etiqueta hacia  
arriba.  
selección y presione [ENTER] para  
confirmar la selección.  
REANUDACIÓN  
DVD-V  
CD  
1
Durante la reproducción, presione  
[STOP C].  
4
Presione [PLAY O].  
¡Aparecerá el mensaje de continuación en la pantalla  
¡La bandeja se cerrará automáticamente y la  
reproducción comenzará desde el primer capítulo o  
pista del disco.  
de TV.  
2
Presione [PLAY O], la reproducción continuará  
desde el punto donde se paró la reproducción.  
¡La reproducción también empieza cerrando  
manualmente la bandeja del disco o presionando  
[OPEN/CLOSE A].  
¡Si la reproducción no comienza automáticamente,  
presione [PLAY O].  
¡Cuando reproduzca un DVD que tenga grabado un  
menú de títulos, el menú podrá aparecer en la pantalla.  
¡Para cancelar la continuación, presione dos veces  
[STOP C].  
¡La información de continuación permanece activada  
incluso cuando apaga el interruptor principal.  
5
Presione [STOP  
C] para detener la reproducción.  
- 38 -  
ES  
 
MEMO  
- 39 -  
ES  
 
FUNAI CORPORATION  
LIMITED WARRANTY  
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship  
as follows:  
DURATION:  
PARTS:  
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the  
date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this  
warranty.  
LABOR:  
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date  
of original retail purchase.  
LIMITS AND EXCLUSIONS:  
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail  
purchase will be required together with the product to obtain service under this warranty.  
This warranty shall not be extended to any other person or transferee.  
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing  
or if service was attempted by an unauthorized service center. This FUNAI CORPORATION Limited warranty does  
not apply to any product not purchased and used in the United States.  
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It  
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not  
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,  
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this  
product or damage which results from fire, flood, lightning or other acts of God.  
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE  
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.  
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY  
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE  
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL  
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF  
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS  
REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE  
PERFORMED BY A FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS ONLY VALID WHEN  
THE UNIT IS CARRIED-IN TO A FUNAI AUTHORIZED SERVICE FACILITY.  
IMPORTANT:  
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS  
THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE  
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI  
CORP.  
ATTENTION:  
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT  
WITHOUT PRIOR NOTICE.  
To locate your nearest Authorized Service Center or for general service inquiries, please call or  
write to the following:  
FUNAI CORPORATION, INC.  
SERVICE CENTER  
19900 Van Ness Avenue, Torrance, CA 90501  
Tel :1-800-242-7158  
Head Office: 100 North Street, Teterboro, NJ 07608  
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.  
Printed in Malaysia  
1EMN20326  
T9102UC ★★★★★  
 

Snapper Lawn Mower 1690583 User Manual
Sony Digital Camera DSC F505 User Manual
Sony MP3 Docking Station SRSBTX500 User Manual
Sony Portable CD Player MZ E501 User Manual
SOYO Computer Hardware SY 6VBA 133 User Manual
Speco Technologies Computer Monitor PVM 2 User Manual
Sterling Plumbing Product e049400 User Manual
Subaru Robin Power Products Laptop RGX2900 User Manual
SunBriteTV Flat Panel Television 46 006 4660HD 111005 User Manual
Sylvania TV VCR Combo 6313CB 6319CB User Manual