PS2-WLC Controller
Playstation®, PS2, PSone and PSX are registered trademarks of Sony Computer
Entertainment, Inc. This product is not sponsored, endorsed or approved by Sony Features
and/or specifications subject to change without notice.
Connection plug
RX-LED
User guide
CONNECT button
POWER-LED
We hope you enjoy using our PS2™ 2.4 GHz wireless controller. Please read this guide
thoroughly before using the unit.
4-WAY button
TURBO button
SELECT button
PROGRAM button
START button
CONNECT button
ꢀ button
1. Product description
This device is a wireless controller specifically for use with PlayStation2™. It can also be used
with PSONE™ and PSX™. The controller works at a frequency of 2.4 GHz, has a double
vibration feature as well as all other functions of the original SONY units. The controller also
has Turbo and Program functions.
2. Included
1 Controller; 1 receiver; 1 user manual
U button
{ button
3. Product features
X button
Power Supply:
Operating time:
Transmission:
3 x 1.5 V AAA batteries
More than 6 hours
2.4 GHz multi-channel transmission
10 m
RIGHT ANALOGUE JOY-
STICK (when pressed:
R3)
Range of action:
Special functions:
Turbo function, programmable buttons with memory,
forced connection
RX-LED
ANALOGUE button
MODE-LED
4. Connecting the receiver
LEFT ANALOGUE JOY-
STICK (when pressed: L3)
Insert the receiver plug
into the appropriate slot on the PlayStation™ console and then
switch on the PlayStation™. The POWER-LED
on the receiver will come on. The RX-
X button
LED will remain on as soon as the receiver is connected to the controller.
R1 button
5. Inserting / replacing the batteries
ON/OFF switch
Battery compartment
Before using the controller insert the batteries into the battery compartment on the back of the
unit. To do this, open the battery compartment , insert the new batteries according to the
polarity and close the compartment. Please ensure the controller has been switched off before
you replace the batteries. Please also read the information on safe disposal of batteries.
L1button
L2button
- 1 -
PS2-WLC Controller
ƒ Never mix battery types and never mix old and new batteries. Replace the batteries as
soon as they become too weak or where the unit has not been used for some time.
ƒ There is a risk of explosion if the batteries are not replaced in the proper manner. Please
ensure the batteries are always inserted according to the correct polarity. Replace the
batteries with the same brand or similar batteries. Risk of explosion when batteries are
replaced incorrectly.
ƒ Do not attempt to recharge a non-rechargeable battery. There is a risk of explosion.
ƒ Batteries / rechargeable batteries can be fatal if swallowed. Please store batteries out of
reach of small children. Seek medical help immediately if a battery has been swallowed.
ƒ Do not expose the batteries to heat or flames. Never short-circuit batteries; never try to
force open batteries; never attempt to recharge non-rechargeable batteries. Batteries may
otherwise explode and cause serious injury.
The RX-LED
flashes when performing the TURBO function.
comes when on you are setting the TURBO function; the RX-LED
12. Button programming function:
You can program and save the button sequence using the PROGRAM function.
Setting the PROGRAM functions: Press the PROGRAM button . The RX-LED
light will come on. Now press the button which you want to programme with a combined
function. Then press the desired button sequence (a maximum of 15 buttons) finish by
pressing the PROGRAM button.
The RX-LED light will go out.
15. Disposing of batteries
Clearing the PROGRAM functions: Press the PROGRAM button
once. The
Please note that you, as the end user, are required to return used batteries to a public
or privately run battery disposal unit.
RX-LED light will come on. Press the button which you previously programmed and want
to clear. Press the PROGRAM button once again. The RX-LED goes out, i.e. the
PROGRAM function has been cleared.
The following buttons can be programmed with combined functions: L2, L3, R2, R3. The
following buttons can be used for programming: U, {, X, ꢀ, all 4 directional buttons, L1,
L2, L3, R1, R2 and R3. When you switch off the unit the controller retains the last
16. Disposing of the unit
Please note that this device is subject to European Directive 2002/96/EC on the
reduction of electronic waste.
ƒ You are not permitted to dispose of this unit together with household
PROGRAM function setting. The RX-LED
PROGRAM function; the RX-LED flashes when you are using the PROGRAM function.
remains on when you are setting the
waste.
ƒ Information on safe disposal of all devices is available from your local
council, waste disposal unit and the shop in which you purchased this
product.
ƒ You may deposit this product free of charge in your community collection
Note:
Not every game supports button sequence programming.
facility.
ƒ Correct disposal of used goods protects the environment as well as your
13. Vibration mode
The unit vibrates once briefly to confirm when you press the R3 and SELECT buttons. This
is to indicate that all vibrations (strong and weak) have been deactivated. Press the same
button again to reactivate the vibration mode. This is confirmed by two short vibrations.
health.
17. Guarantee
This product comes with a three-year guarantee starting on the day of purchase. If this product
is faulty send it, together with the receipt and a stamped-addressed envelope, to:
14. Safety advice
ƒ Do not attempt to dismantle, modify or repair the unit yourself.
JNC Datum Tech GmbH, Support Center,
Maltschachstrasse 32, D - 72144 Dusslingen, Germany.
ƒ Do not use this unit together with other electronic equipment of the same operating
frequency to avoid damaging both units.
ƒ Please ensure no fluids or small pieces of metal can get inside the unit. Avoid knocks to
the unit and do not place heavy objects on the device. Do not place containers of liquid like
vases or drinking glasses on or near the unit and never immerse the unit in fluid.
ƒ Do not use or store the unit in high-temperature areas, or in steamy, smoky or dusty areas.
Manufacturer:
JNC Datum Tech GmbH
Benzstraße 33
More information can also be found at:
D - 71083 Herrenberg
Germany
- 3 -
|