Silvercrest Hot Beverage Maker SWKD 3000 A16 User Manual

KITCHEN TOOLS  
6
Kettle SWKD 3000 A1  
Kettle  
Operating instructions  
KOMPERNASS GMBH  
BURGSTRASSE 21 · D-44867 BOCHUM  
ID-Nr.: SWKD3000A1-07/10-V3  
IAN: 54351  
 
Content  
Page  
Intended use  
2
2
2
2
3
3
4
5
6
7
7
7
8
Technical data  
Items supplied  
Safety Information  
Operating elements  
Commissioning  
Heating water  
Keeping water hot  
Cleaning and Care  
Storage  
Disposal  
Warranty and Service  
Importer  
Read the operating instructions carefully before using the appliance for the first time and preserve this  
booklet for later reference. Pass the manual on to whomsoever might acquire the appliance at a later date.  
- 1 -  
 
KETTLE  
Safety Information  
Intended use  
ƽ To avoid potentially fatal electric  
shocks:  
This appliance is intended for the boiling and kee-  
ping hot of drinking water in domestic households. It  
is not intended for use with other fluids or for com-  
mercial applications.  
• Ensure that the base with the electrical connections  
NEVER comes into contact with water! Should  
the base be accidentally moistened, allow it to  
dry completely before using it.  
• Use the kettle only with the supplied base.  
• Ensure that during operation the power cable  
never becomes wet or damp. Lay it so that it  
cannot be pinched or otherwise damaged.  
• Arrange for defective plugs and/or power cables  
to be replaced at once by authorised technicians  
or our Customer Service Department.  
• After use, ALWAYS remove the plug from the  
mains power socket. Simply switching off is not  
sufficient, because the appliance remains "live"  
for as long as the plug is inserted in the mains  
power socket.  
Technical data  
Mains voltage:  
220 - 240 V / 50 Hz  
~
Power consumption  
Operation:  
Standby:  
2500 - 3000 W  
< 1 W  
To bring 1 Liter of water to the boil:  
15°C --> 100°C/Power consumption: < 117 Wh  
Capacity:  
max. 1.5 l  
min. 0.5 l  
ƽ To avoid burn and injury risks:  
• Heat water only with the lid closed, otherwise  
the automatic switch-off cannot function. Boiling  
water could then be sprayed out over the edge.  
• Hot steam clouds may be released. In addition,  
the kettle becomes very hot when in use.  
Therefore wear oven-mitts.  
Due to the high power consumption, in older  
electrical installations the fuse (12A) could  
trigger.  
• Ensure that the appliance is stood stably and  
vertically before switching it on.  
Items supplied  
Boiling water can cause an unstable appliance  
to tip over.  
Kettle  
Base  
Operating manual  
Check the contents for completeness directly after  
unpacking.  
Remove all packing material.  
- 2 -  
 
• This appliance is not intended for use by individuals  
(including children) with restricted physical, physio-  
logical or intellectual abilities or deficiences in  
experience and/or knowledge unless they are  
supervised by a person responsible for their  
safety or receive from this person instruction in  
how the appliance is to be used.  
Commissioning  
ƽ Important  
Always and only use freshly drawn mains water in  
the kettle! Do not consume any water that is not  
certified as potable. If you do, you are taking  
a risk with your health!  
• Children should be supervised to ensure that  
they do not play with the appliance.  
• Do not use an external timing switch or a separate  
remote control system to operate the appliance.  
• Before using the appliance, check to ensure  
that ...  
– the appliance, plug and power cable are in  
a faultfree condition and...  
Operating elements  
– the cable is completely unwound from the cable  
winder  
under the base  
and...  
u
y
Temperature LEDs  
KEEP WARM button  
ON / OFF switch  
SET TEMP button (Temperature adjustment)  
Handle of the lid  
(with subjacent lid opener)  
Base  
Cable winder  
– the cable is guided through the recess on the  
q
w
e
r
t
base and...  
y
– all packaging materials have been removed  
from the appliance.  
• Fill the appliance with water up to the MAX  
marking on the scale and let it come to a full  
boil once – as described in the next section.  
• Pour this water away after boiling it.  
• Rinse the kettle with clean water.  
• Fill the appliance once again with water up to  
the MAX marking on the scale and then bring  
it to the boil. Pour this water away also after  
boiling it.  
y
u
i
Pourer sieve  
The appliance is now ready for use.  
Note  
If there is no or not enough water in the kettle, then the  
appliance switches itself off automatically. Lift the  
kettle from the base  
and fill it with water to take  
y
the appliance back into use.  
- 3 -  
 
Heating water  
You can now heat the water up:  
• Set the desired temperature:  
press the button SET TEMP  
ƽ Danger  
repeatedly until  
r
NEVER place the electrical base  
water – a potentially fatal risk!  
adjacent to  
the LED  
at the desired temperature glows.  
y
q
You can choose between 40°C, 60°C, 80°C  
and 100°C.  
Note  
Always use freshly drawn water. Do not consume  
any water that has already stood in the kettle for  
longer than one hour. Do not reboil water that has  
cooled down. Always pour old water away.  
Microbes could have formed in it!  
Information  
If you cannot set the desired temperature, it may be  
because the temperature of the water in the kettle is  
still too high. In this case, exchange the water for  
freshly drawn mains water.  
Note  
• When you selected the desired temperature,  
When possible, heat only as much water as you  
actually need. This also saves energy!  
press the On/Off button  
within about 10 se-  
e
conds. The LED  
of the selected temperature  
q
blinks. The LED integrated in the On/Off button  
e
• Lift the kettle off of the base when filling it!  
glows. If you do not start the boiling process wit-  
• Open the lid by pressing the lid switch under the  
hin 10 seconds the set temperature lapses.  
handle of the lid , thereby opening the lid up.  
• Once the desired temperature has been reached,  
t
Pull the lid back slightly so that it is secure and  
a signal tone sounds, the respective LED  
for  
q
does not drop down.  
the temperature reached is lit constantly for  
about 2 minutes and the LED integrated in the  
On/Off switch extinguishes.  
• When filling it, hold the kettle upright . Only in  
this way can you correctly read the markings.  
Fill the kettle...  
e
– at least to the MIN mark, so that the appliance  
does not overheat,  
Information  
If you want to bring water to a boil (100°C), you  
– no more than to the MAX mark, so that no boiling  
water spills out.  
only need to press the On/Off button . The  
kettle will bring the water to a boil.  
e
• First close the lid, ensuring that it engages...  
• and then place the kettle on the base , such  
Information  
- You can cancel the heating up of the water at  
y
that it is standing absolutely upright on the base  
.
any time by pressing the On/Off button  
.
e
y
• Insert the plug into a mains power socket.  
- Once you lift the kettle from the base , the  
y
appliance switches all functions off. All settings are  
cancelled.  
- 4 -  
 
Note  
The keep-warm setting can be made before, during  
or immediately after the boiling process:  
Do not let the water stand in the kettle for longer  
than is absolutely necessary. That would lead to  
scale deposits. Pour away the water that is no lon-  
ger required immediately.  
Before the boiling process  
• Before the boiling process, press the KEEP  
WARM  
button.  
w
• Press the button SET TEMP  
repeatedly until  
r
Keeping water hot  
the LED  
at the desired temperature glows.  
q
• Press the button Start to begin the boiling and  
With this kettle you can maintain the water at a  
temperature of (about) 40°C, 60°C, 80°C or  
100°C for 30 minutes. Should you have set the  
desired temperature maintenance at 100°C, to  
avoid excessive steam development the kettle holds  
the water at a temperature of between about 90°C  
and 100°C. If the desired heating maintenance  
temperature is 80°C, 60°C or 40°C, the water he-  
ater holds the water at a temperature of between  
about 8°C above or below the selected temperatu-  
re.  
then the keep-warm process.  
The LED  
of the currently set temperature glows,  
q
the LED integrated in the KEEP WARM  
glows as well as the LED in the On/Off  
The water will now also be kept warm after being  
heated.  
button  
w
button.  
e
During the boiling process  
• Start the boiling process as described in the  
section "Heating water".  
• During the boiling process, press the KEEP  
WARM  
button.  
w
ƽ Important  
On completion of the boiling process the LED  
the currently set temperature glows, the LED integra-  
of  
q
Use the keep-warm function only when there is at  
least 0.5 liters of water in the kettle. If there is less  
water in it, the kettle may be switched off within the  
30 minutes in order to protect the heating element.  
ted in the KEEP WARM  
the LED in the On/Off  
button glows as well as  
button.  
w
e
The water will now also be kept warm after being  
heated.  
ƽ Warning  
BEFORE you lift the kettle from the base , first  
After the boiling process  
y
disconnect the plug from the mains power socket. This  
prevents causing a short circuit by water possibly spil-  
ling out of the kettle and falling onto the live  
• After the signal tone, indicating the end of the  
boiling process, press the button KEEP  
WARM  
.
w
electrical connections in the base  
.
The appliance will then automatically maintain the  
y
keep-warm temperature at the temperature you  
ƽ Risk of personal injury  
selected to heat the water. The LED  
of the cur-  
q
For safety reasons, the lid should not be opened  
while the water is boiling or is very hot. There is  
a risk of receiving severe scalds.  
rently set temperature glows, the LED integrated  
in the KEEP WARM button glows as well as the  
w
LED in the On/Off  
be kept warm.  
button. The water will now  
e
- 5 -  
 
As soon as the water temperature falls below the set  
temperature, the kettle heats up again automatical-  
Before cleaning the appliance, ....  
• first disconnect the plug from the mains power  
socket and allow the appliance to cool down.  
• Clean all exterior surfaces and the power cable  
with a slightly moist cloth. In all cases, dry the  
appliance well before using it again.  
ly. The LED  
of the currently selected temperature  
q
setting blinks until the selected temperature has  
been regained. Afterwards, it glows constantly  
again.  
After 30 minutes the kettle switches itself off. Two  
signal tones sound. All LEDs extinguish.  
• To clean the inside of the kettle, thoroughly rinse  
it out with water and then pour the water away.  
• Do not use detergents, abrasives or solvents.  
These can damage the appliance.  
Information  
- At any time you can cancel the temperature main-  
tenance of the water by pressing the On/Off  
In the event of scale deposits:  
button  
or the KEEP WARM button  
.
• Before descaling, remove the pourer sieve  
e
w
i
- Once you lift the kettle from the base , the  
(see chapter "Removing/replacing the pourer  
y
appliance switches all functions off.  
sieve").  
• Use a descaler designed for household appliances  
(e.g. for coffee machines). Pay heed to the in-  
structions given for the descaler.  
• For the stainless steel container bottom, you can  
use a suitable product from a specialist dealer.  
Note  
Do not let the water stand in the kettle for longer  
than is absolutely necessary. That would lead to  
scale deposits. Pour away the water that is no  
longer required.  
Removing/replacing the pouring sieve  
• Open the lid.  
Cleaning and Care  
• Press the tab at the upper end of the pourer  
sieve  
down and, simultaneously, push the  
i
ƽ Danger  
pourer sieve to the inside.  
• You can then lift the pourer sieve  
of its holder.  
Do not open any part of the housing. There are no  
user-serviceable elements inside. An open housing  
increases the risk of receiving a potentially fatal  
electric shock.  
up and out  
i
• Clean the pourer sieve with a lightly moistened  
i
dishcloth and under running water.  
• After cleaning, insert the pourer sieve  
from  
i
Under NO circumstances may the appliance  
parts be immersed in water or other liquids!  
Should residual liquid be on "live" parts during  
use, there would be the risk of receiving a  
potentially fatal electric shock.  
above and then push it forward so that the tab  
locks into place. Ensure that the pourer sieve  
grips into the holder at the lower end and is  
firmly seated.  
i
- 6 -  
 
• Should any scale deposits have set on the pourer  
Warranty and Service  
sieve , soak it for a few hours in a water-vinegar  
i
solution at a ratio of 6:1. The scale deposits will  
You receive a 3-year warranty for this appliance  
of the purchase date. This appliance has been  
manufactured with care and meticulously examined  
before delivery.  
dissolve themselves. Rinse the pourer sieve  
with copious amounts of clear water.  
i
Please retain your receipt as proof of purchase. In  
the case of a warranty claim, please make contact  
by telephone with our Customer Service Depart-  
ment. Only in this way can a post-free despatch for  
your goods be assured.  
Storage  
Let the appliance cool completely before putting it  
in storage.  
• Wrap the cable around the cable winder  
The warranty covers only claims for material and  
manufacturing defects, not for transport damages,  
wearing parts or for damage to fragile components,  
e.g. buttons or batteries. This product is for private  
use only and is not intended for commercial appli-  
cations.  
In the event of misuse and improper handling, use  
of force and interference not carried out by our au-  
thorized service branch, the warranty will become  
void. Your statutory rights are not restricted in any  
way by this warranty.  
u
under the base  
.
y
• Store the appliance at a dry location.  
Disposal  
Do NOT dispose of the appliance in  
your normal domestic waste. This  
product is subject to the provisions of  
European Directive 2002/96/EC.  
The warranty period is not extended by repairs ef-  
fected under warranty. This applies also to replaced  
and repaired parts. Damages or defects discovered  
after purchase are to be reported directly after un-  
packing, at the latest two days after the purchase  
date. Repairs carried out after lapse of the warranty  
period are subject to charge.  
Dispose of the appliance through an approved dis-  
posal centre or at your community waste facility.  
Observe the currently applicable regulations.  
In case of doubt, please contact your waste disposal  
centre.  
Dispose of all packaging materials in an  
environmentally friendly manner.  
DES UK LTD  
Tel.: 0871 5000 700 (£ 0.10 / minute)  
Kompernass Service Ireland  
Tel.: 1850 930 412 (0,082 EUR/Min.)  
Standard call rates apply. Mobile operators may vary.  
CY  
Kompernass Service Cyprus  
Tel.: 800 9 44 01  
- 7 -  
 
Importer  
KOMPERNASS GMBH  
BURGSTRASSE 21  
44867 BOCHUM, GERMANY  
- 8 -  
 

Sharp Computer Monitor LL T17D4 User Manual
Sharp PDAs Smartphones YO P20 User Manual
Sherwood Stove EG40 DV User Manual
SIIG Computer Drive 104 0561C User Manual
Sony Car Video System CDP C260Z User Manual
Sony Cassette Player 453V User Manual
Sony Music Mixer XDCAM User Manual
Sunbeam Convection Oven BT7000 User Manual
Sunbeam Gas Grill WG4610HP User Manual
Tannoy Cell Phone T250I User Manual