6
Clock Radio SRD 250 A1
Clock Radio
Operating instructions
KOMPERNASS GMBH
BURGSTRASSE 21 · D-44867 BOCHUM
ID-Nr.: SRD 250 A1-01/11-V2
IAN: 61030
Index
GB
IE
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Information for these operating instructions . . . . . . . . . . . . . . . . . 3
Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Danger from electric shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Interaction with batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Basic Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operating components. . . . . . . . . . . . . . . . . . . . . . . . . 8
Setting up and connecting . . . . . . . . . . . . . . . . . . . . . . 9
Package contents and transport inspection. . . . . . . . . . . . . . . . . . 9
Set-up location requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Inserting the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Providing mains power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
VHF wire antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Handling and operation . . . . . . . . . . . . . . . . . . . . . . . 11
Setting the time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Radio operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Programming the wake time and method . . . . . . . . . . . . . . . . . . 13
Switching the alarm function on . . . . . . . . . . . . . . . . . . . . . . . . . 14
Switching the alarm off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Switching the alarm function off . . . . . . . . . . . . . . . . . . . . . . . . . 14
SRD 250 A1
1
Snooze function (“SNOOZE” function) . . . . . . . . . . . . . . . . . . . 14
Automatic Switch-off (“SLEEP” function) . . . . . . . . . . . . . . . . . . . 14
Setting the display illumination . . . . . . . . . . . . . . . . . . . . . . . . . . 15
GB
IE
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Malfunction causes and remedies. . . . . . . . . . . . . . . . . . . . . . . . 16
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Disposal of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Disposing of the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Information regarding the EG Conformity Declaration. . . . . . . . 19
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Importer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
SRD 250 A1
2
Introduction
Introduction
GB
IE
Information for these operating instructions
These operating instructions are a component of the SRD 250 A1
Clock Radio (henceforth designated as the appliance) and they
supply you with important information about the intended use,
safety and connection as well as operation of the appliance.
These operating instructions must be kept available close to the
appliance. They are to be read and used by anyone assigned to
operate and repair faults in the appliance. Retain these operating
instructions and pass them on to any future owners with the appliance.
Copyright
This documentation is copyright protected.
Any copying and/or reproduction, wholly or partially, as well as
rendition of the illustrations, also in a modified form, is permitted
only with written consent from the manufacturer.
Intended use
This device is intended exclusively for listening to radio programmes
and for waking by an alarm tone or radio in a domestic environment.
This appliance is not intended for any other use or for uses beyond
those mentioned. Claims of any kind for damage caused by improper
use, incompetent repair, unauthorized modification or the use of
unauthorized parts are excluded. The risks from these are borne
entirely by the user.
SRD 250 A1
3
Introduction
In these operating instructions the following warnings are used:
GB
IE
DANGER
A warning at this danger level indicates a threatening
dangerous situation.
In the event that the hazardous situation is not avoided it can lead
to death or serious injury.
► Compliance to the instructions in this warning are necessary
to avoid the danger of death or serious injury.
WARNING
A warning at this danger level indicates a potentially
dangerous situation.
If the dangerous situation is not avoided it can lead to injuries.
► The directives in this warning are there to avoid personal injuries.
IMPORTANT
A warning of this danger level signifies possible
property damage.
If the situation is not avoided it can lead to property damage.
► The directives in this warning are there to avoid property damage.
NOTE
► A notice signifies additional information that assists in the
handling of the appliance.
SRD 250 A1
4
Safety
Safety
GB
IE
In this chapter you receive important safety information regarding
handling of the appliance. This appliance complies with the statu-
tory safety regulations. Incorrect usage can lead to injuries and
property damage.
Danger from electric shock
DANGER
Life-threatening situation from electric shock!
A life-threatening situation can arise from contact
with live wires or components!
Observe the following safety instructions to avoid electric shock
hazards:
► Do not use the appliance if the mains power plug or the
connection cable are damaged.
► Do not, under any circumstances, open the appliance housing.
The risk of an electric shock is present if the power carrying
connections are touched and the electrical and mechanical
construction is changed.
► The appliance consumes power when in standby-mode.
To completely separate the appliance from mains power, the
power plug MUST be removed from the mains power socket.
The appliance should be positioned so that you have unrestricted
access to the mains power socket at all times, thus enabling
the plug to be immediately withdrawn should an emergency
situation arise.
SRD 250 A1
5
Safety
Interaction with batteries
GB
IE
WARNING
Danger from improper use!
For safe handling of batteries observe the following safety
instructions:
► Do not throw batteries into a fire.
► Do not short circuit batteries.
► Do not attempt to recharge batteries.
► Never open, solder or weld batteries. The risk of explosions
and injuries exists.
► Regularly check the condition of the batteries. Leaking battery
acid can cause permanent damage to the appliance. Special
caution should be shown when handling damaged or leaking
batteries. Danger from acid burns! Wear protective gloves.
► Store batteries in a place inaccessible to children.
When swallowed seek immediate medical attention.
► If you do not intend to use the appliance for an extended
period of time, remove the batteries.
Basic Safety Instructions
For safe handling of the appliance observe the following safety
information:
■ Before use check the appliance for visible external damage. Do
not put into operation an appliance that is damaged or has been
dropped.
■ Damaged cables or connections should be replaced by authorised
qualified persons or by the customer service department.
SRD 250 A1
6
Safety
■
Persons who, due to their physical, intellectual or motor abilities,
are incapable of operating the appliance safely may only use the
device under supervision or direction from a responsible person.
GB
IE
■ Only permit children to use the appliance under supervision.
■ Repairs should only be carried out by authorised specialist companies
or by the customer service department. Incorrect repairs can result in
danger to the user. In addition warranty claims become void.
■ A repair to the appliance during the warranty period may only
be carried out by a customer service department authorised by
the manufacturer otherwise no additional warranty claims can
be considered for subsequent damages.
■ Defective components may only be replaced with original replace-
ment parts. Only by using original replacement parts can you
guarantee that the safety requirements are complied with.
■ Protect the appliance from moisture and liquid penetration. Never
submerge the appliance in water, do not place the appliance in
the vicinity of water and do not stand any object filled with liquid
(i.e. vases) on the appliance.
■ Do not place any objects on the appliance.
■ Do not operate the appliance in the vicinity of open flames
(i.e. candles).
■ Avoid direct sunlight.
■ Always pull on the power plug when disconnecting from the wall
socket, never pull on the connection cable.
■ If malfunctions occur or thunder storms threaten pull the power
plug from the wall socket.
SRD 250 A1
7
Operating components
Operating components
GB
IE
SNOOZE Button: Alarm interupt
Display
2
3
POWER-LED: Lights up when the device is switched on
MHz-LED: Lights up with VHF reception
kHz-LED: Lights up with MW reception
SLEEP-LED: Lights up when the SLEEP function is switched on
TUNING regulator: Station selection
Wire antenna
4
5
6
7
8
9
POWER/BAND button: Switch device on / off /
select frequency band
10
11
12
DOWN button: Adjustments downwards
Battery compartment
UP button: Adjustments upwards
13 TIME button: Set the time
14 SLEEP button: Set the automatic switch off
15 AL2 button: Set Alarm time 2
16 AL1 button: Set Alarm time 1
17 Power Cable
18 VOL control: Volume control
19 DIMMER switch: Set the display illumination
SRD 250 A1
8
Setting up and connecting
Setting up and connecting
GB
IE
Package contents and transport inspection
The appliance is delivered with the following components as
standard:
● Clock Radio
● Operating instructions
Extract the appliance and the instruction manual from the carton
and remove all packaging material.
NOTE
► Check the contents to ensure everything is present and there
are no signs of visible damage.
► If the contents are not complete or are damaged as a result
of defective packaging or through transportation, contact the
Service Hotline (see chapter Service).
Set-up location requirements
For safe and fault free operation of the appliance the set-up
location must comply with the following provisions:
■ Place the appliance on a firm, flat and even surface .
■ Place the appliance so that the ventilation slots are not covered.
■ Do not place the appliance in a hot, wet or very humid location
or in the vicinity of flammable materials.
SRD 250 A1
9
Setting up and connecting
■ The surfaces of furniture may contain components that can affect
the rubber pads of the appliance and could soften them. If neces-
sary, place a covering under the appliance's rubber pads.
GB
IE
■ The mains power socket must be easily accessible so that, in an
emergency, the plug can be quickly withdrawn from the socket.
Electrical connection
■ Before connecting the appliance compare the connection data
(Voltage and frequency) on the rating plate with that of the mains
electric source. This data must be compatible to avoid possible
damage to the appliance.
■ Make sure that the appliance's connection cable is not damaged
and is not laying over hot surfaces and/or sharp edges.
■ Make sure that the connection cable is not tightly stretched or bent.
■ Do not allow the connection cable to hang over edges
(Trip wire effect).
Inserting the batteries
By inserting two 1.5 V batteries (type R6/LR6/AA/Mignon) you
avoid losing the programmed time of day and wake time in the
event of mains power loss. The batteries make sure that the internal
clock continues to run even during a power outage.
When power is restored the correct time appears automatically
2
in the display
.
NOTICE
► The display, radio and alarm do not function with battery-
power alone.
SRD 250 A1
10
Handling and operation
11
on the bottom of
♦
♦
Open the cover of the battery compartment
the device.
GB
IE
Insert two 1.5 V batteries type R6/LR6/AA/Mignon (not supplied)
11
into the battery compartment . For correct polarity make sure
that the batteries are inserted according to the diagram in the
11
battery compartment
.
11
by replacing the cover and
♦
Close the battery compartment
allowing it to lock into place.
Providing mains power
♦
Plug the mains power plug into a wall socket. The time of day
2
(- -:- -) will be shown in the display
.
VHF wire antenna
8
♦
For VHF reception completely unfold the wire antenna
.
Handling and operation
In this chapter you receive important information for the handling
and operation of the appliance.
Setting the time
2
♦
♦
♦
♦
♦
Press and hold the TIME button 13. In the display
indicator blinks.
the hour
12
10
10
Press or hold down the UP button
to set the hour.
and/or DOWN button
2
Press the TIME button 13 again. In the display
the minute
indicator blinks.
12
Press or hold down the UP button
to set the minutes.
and/or DOWN button
Press the TIME button 13 again. The set time of day will be accepted.
SRD 250 A1
11
Handling and operation
NOTICE
GB
IE
► The time of day will revert back to - -:- - if the device is discon-
nected from the mains power supply and no batteries have
been inserted.
Radio operation
9
♦
♦
♦
Press the POWER/BAND button
to switch the device on.
With the VOL control 18 set the desired sound level.
9
Press briefly the POWER/BAND button
to set the desired
4
frequency band. With VHF reception the MHz-LED
lights up,
5
with MW reception the kHz-LED
lights up.
7
♦
♦
With the TUNING control
set the desired radio station.
9
Press for approx. two seconds the POWER/BAND button
switch the device off.
to
NOTE
►
The technical realities of the appliance permit an adjustable
frequency range outside the permitted frequency ranges
of VHF (FM) 87.5 - 108 MHz and/or MW (AM) 526,5 -
1606,5 kHz. In some countries, different national regulations
may apply to the assigned radio frequency ranges. Please
note that information received outside of the assigned radio
frequency ranges may not be used, passed on to third parties
or otherwise misused.
SRD 250 A1
12
Handling and operation
Programming the wake time and method
GB
IE
When programming the alarm times, you can select whether,
at the programmed time, alarm tones should sound or the radio
should start playing. Two different alarm times (Alarm 1/Alarm 2)
can be programmed.
2
♦
♦
♦
♦
♦
Press and hold the AL1 button 16 or AL2 button 15. In the display
the hour indicator blinks.
10
or DOWN button
12
Press or hold down the UP button
to set the hour.
2
Press the AL1 button 16 or AL2 button 15 again. In the display
the minute indicator blinks.
10
or DOWN button
12
Press or hold down the UP button
to set the minutes.
Press the AL1 button 16 or AL2 button 15 again. The set wake
2
time is accepted and in the display
indicator.
appears the wake method
12
♦
♦
Press the UP button
Alarm tone or
to set the desired wake method (
= Radio).
=
Press the AL1 button 16 or AL2 button 15 again to accept the
setting.
NOTICE
► If you want to be awakened with the radio, apart from the wake
time programming you must also set, additionally, the desired
radio station and volume (see section Radio operation).
SRD 250 A1
13
Handling and operation
Switching the alarm function on
GB
IE
♦
Press briefly the AL1 button 16 and/or AL2 button 15. In the dis-
2
play
a point appears to the left and/or to the right. The alarm
function is now activated.
Switching the alarm off
9
♦
Whilst the alarm is sounding press the POWER/BAND button
to switch the alarm off for 24 hours.
,
Switching the alarm function off
♦
Press briefly the AL1 button 16 and/or AL2 button 15. The alarm
2
indicators go out in the display
.
Snooze function (“SNOOZE” function)
♦
Whilst the alarm is sounding press the SNOOZE button to tempo-
rarily switch off the alarm. After 6 minutes the alarm sounds again.
NOTICE
► If the snooze function is activated the corresponding alarm
2
point blinks in the display
.
Automatic Switch-off (“SLEEP” function)
With the “Sleep” function the device switches itself off after a time
lapse of between 60 and 10 minutes.
9
♦
♦
Press the POWER/BAND button
to switch the device on.
2
Press the SLEEP button 14. In the display
time 60 minutes and the SLEEP-LED
appears the switch off
6
lights up. Repeated press-
ing of the SLEEP button 14 shortens the switch off time by
10 minutes respectively.
SRD 250 A1
14
Cleaning
♦
Press repeatedly the SLEEP button 14 until the desired
GB
IE
2
switch of time is shown in the display
.
14
♦
To switch off the sleep function press repeatedly the SLEEP button
,
6
2
until in the display
is shown. The SLEEP-LED
goes out.
Setting the display illumination
19
♦
Set the DIMMER switch
to HIGH if you want the indicators in
2
the display
to appear brighter.
19
♦
Set the DIMMER switch
to LOW if you want the indicators in
to appear darker.
2
the display
Cleaning
DANGER
Risk of fatal electrocution!
► Remove the plug from the mains power socket before cleaning.
► Whilst cleaning make sure that no moisture is allowed to enter
the device.
► Do not use aggressive cleaning agents or scouring powder.
These can affect the surfaces of the device.
■ Clean the surfaces of the device with a soft, dry cloth.
SRD 250 A1
15
Troubleshooting
Troubleshooting
GB
IE
In this chapter you will receive important information for the locali-
sation of malfunctions and their remedies. Observe the instructions
in order to avoid danger and damage.
Malfunction causes and remedies
The following table will help with localizing and remedying minor
malfunctions:
Defect
Possible cause
Solution
The plug is not
inserted.
Insert the plug into the
mains power socket.
Appliance
does not
switch on.
Mains power socket
is not supplying
power.
Check the circuit fuse.
Increase the sound
volume with the
VOL regulator 18.
The volume is set to
minimum.
No sound
The radio station
is not properly
tuned in.
Tune in the radio station
properly with the TUNING
regulator 7 .
Noisy radio
reception
Try to improve reception
by moving the wire
Reception is
too weak.
8
antenna
.
NOTE
► If you cannot solve the problem with the aforementioned
methods, please contact Customer Service .
SRD 250 A1
16
Storage/Disposal
Storage
GB
IE
If you do not intend to use the appliance for an extended period
of time, disconnect it from the mains power supply, remove the
battery and store it at a clean, dry location that is not subjected
to direct sunlight.
Disposal
Disposal of the appliance
Do not dispose of the appliance in your normal
domestic waste. This product is subject to the
provisions of European Directive 2002/96/EC.
Dispose of the appliance through an approved disposal centre or
at your community waste facility. Observe the currently applicable
regulations. In case of doubt, please contact your waste disposal
centre.
Disposing of the batteries
Do not dispose of the batteries with household waste. Every con-
sumer is legally obligated to hand in batteries at a collection centre
in his/her community/district or a dealer. This obligation is intended
to ensure that batteries are disposed of in an environmentally safe
fashion. Hand batteries in only when they are fully discharged.
SRD 250 A1
17
Appendix
Appendix
GB
IE
Technical data
Operational voltage
220-240 V / 50 Hz
2 x 1.5 V battery
Type AA/Mignon/R6/LR6
(Batteries not supplied)
Batteries for power reserve
Power consumption
Operation
10
W
W
Standby
approx. 1.5
Max. Loudspeaker
Output Power
250 mW
Frequency FM (USW)
Frequency AM (MW)
Operating temperature
Humidity (no condensation)
87.5 - 108 MHz
526.5 - 1606.5 kHz
+5 - +40
5 - 90
°C
%
cm
g
Measurements (W x H x D)
14.3 x 13.3 x 8.3
Weight
approx. 435
II
Protection class
SRD 250 A1
18
Appendix
Information regarding the EG Conformity
Declaration
GB
IE
This appliance complies with, in regard to conformance to the basic
requirements and other relevent regulations, the European Directive
for Electromagnetic Compatibility 2004/108/EC, the Low Voltage
Directive 2006/95/EC as well as the Eco-Design Directive
2009/125/EC (Supplement 1275/2008 Appendix II, Nr.1).
The complete original declaration of conformity can be obtained
from the importer.
Warranty
You receive a 3-year warranty for this appliance as of the purchase
date. This appliance has been manufactured with care and meticu-
lously examined before delivery.
Please retain your receipt as proof of purchase. In the case of a
warranty claim, please get in touch, by telephone, with our service
department. Only in this way can a post-free dispatch for your
goods be assured.
NOTE
► The warranty adjustment is valid only for material or manu-
facturing defects not, however, for transport damage, wear
and tear or for damage to breakable parts, i.e. switches or
rechargeable batteries.
This product is for private use only and is not intended for commer-
cial use. The warranty is void in the case of abusive and improper
handling, use of force and internal tampering not carried out by
our authorised service branch.
SRD 250 A1
19
Appendix
Your statutory rights are not restricted in any way by this warranty.
The warranty period will not be extended as a result of warranty
adjustments. This applies also to replacement and repaired parts.
GB
IE
Damage and defects potentially present at the time of purchase
must be reported immediately after unpacking or, at the very least,
two days after date of purchase.
After expiry of the warranty period incidental repairs are subject
to payment.
Service
Service Great Britain
Tel.: 0871 5000 720 (0.10 £/Min.)
E-Mail: [email protected]
Service Ireland
Tel.: 1890 930 034
(0,082 EUR/Min., (peak))
(0,064 EUR/Min., (off peak))
E-Mail: [email protected]
Importer
KOMPERNASS GMBH
BURGSTRASSE 21
44867 BOCHUM, GERMANY
SRD 250 A1
20
|