LQ201U1LW01
TFT-LCD Module
(Model Number: LQ201U1LW01)
Specifications
Spec No.: LD-14115
Dated: May 29, 2002
RECORDS OF REVISION
LQ201U1LW01
SPEC No.
DATE
SUMMARY
NOTE
REVISED
No. PAGE
LD-14115
Feb. 25. 2002
1 st Issue
LD-14115-1
1. Application
This specification applies to the color 20.1 UXGA TFT-LCD module LQ201U1LW01.
◎These specification sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include
materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in
any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express
written permission of SHARP.
◎The device listed in these specification sheets was designed and manufactured for use in OA equipment.
◎In case of using the device for applications such as control and safety equipment for transportation(aircraft,
trains, automobiles, etc. ), rescue and security equipment and various safety related equipment which require
higher reliability and safety, take into consideration that appropriate measures such as fail-safe functions and
redundant system design should be taken.
◎In case of using the device for equipment that requires an extreme level of reliability, such as aerospace
applications, telecommunication equipment(trunk lines), nuclear power control equipment and medical or
other equipment for life support, contact and consult with a SHARP sales representative.
◎SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply
with the instructions and the precautions specified in these specification sheets.
◎Contact and consult with a SHARP sales representative for any questions about this device.
2. Overview
This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor).
It is composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit and a back light unit.
Graphics and texts can be displayed on a 1600×3×1200 dots panel with about 16 million colors by supplying 48
bit data signals(8bit×2pixel×RGB) , two display enable signals, two dot clock signals, +12V DC supply
voltages for TFT-LCD panel driving and supply voltage for back light.
It is a wide viewing-angle-module (Vertical viewing angle:170°Horizontal viewing angle:170°,CR≧10).
LD-14115-2
3. Mechanical Specifications
Parameter
Specifications
Unit
cm
Display size
51 (Diagonal)
20.1 (Diagonal)
Inch
mm
408.0 (H)×306.0 (V)
1600 (H)×1200 (V)
(1 pixel＝R＋G＋B dots)
0.255(H)×0.255 (V)
R,G,B vertical stripe
Normally black
Active area
Pixel format
Pixel
Pixel pitch
mm
Pixel configuration
Display mode
436(W)×335 (H)×27.5 (D)
3.8 (MAX)
Unit outline dimensions *1
Mass
mm
kg
Surface treatment
Anti-glare And hard-coating 2H
*1.Note: excluding back light cables.
The thickness of module (D) doesn’t contain the projection.
Outline dimensions are shown in Fig.1.
LD-14115-3
4. Input Terminals
4-1. TFT-LCD panel driving
CN7A,CN7B (Interface signals and +12VDC power supply)
Using connectors ：DF19G-20P-1H (Hirose Electric Co., Ltd.)
Corresponding connectors ：DF19G-20S-1C (Hirose Electric Co., Ltd.)
DF19G-20S-1F (Hirose Electric Co., Ltd.)
Using LVDS receiver：Contained in a control IC
Corresponding LVDS transmitter：THC63LVDM83R(Thine) or compatible
CN７A
Pin No.
1
Symbol
Vcc
Vcc
Function
Remark
+12V power supply
+12V power supply
Gnd
2
3
Vss
4
Vss
Gnd
5
6
RAIN0-
Negative (-) LVDS differential data input (A port)
LVDS
LVDS
RAIN0+ Positive (+) LVDS differential data input (A port)
7
Vss
Gnd
8
9
RAIN1-
Negative (-) LVDS differential data input (A port)
LVDS
LVDS
RAIN1+ Positive (+) LVDS differential data input (A port)
10
11
12
13
14
15
16
17
18
19
20
Vss
RAIN2-
Gnd
Negative (-) LVDS differential data input (A port)
LVDS
LVDS
RAIN2+ Positive (+) LVDS differential data input (A port)
Vss
CKAIN-
CKAIN+ Positive (+) LVDS differential clock input (A port)
Vss
RAIN3-
RAIN3+ Positive (+) LVDS differential data input (A port)
Vss
BLON
Gnd
Negative (-) LVDS differential clock input (A port)
LVDS
LVDS
Gnd
Negative (-) LVDS differential data input (A port)
LVDS
LVDS
Gnd
Back light ON signal (output) 【Note1】
Pull Up
【Note1】BLON:It change from L to H at 7 frames after Vcc ON.
CN７B
Pin No.
1
Symbol
Vcc
Vcc
Function
Remark
+12V power supply
+12V power supply
Gnd
2
3
Vss
4
Vss
Gnd
5
6
RBIN0-
Negative (-) LVDS differential data input (B port)
LVDS
LVDS
RBIN0+ Positive (+) LVDS differential data input (B port)
7
Vss
Gnd
8
9
RBIN1-
Negative (-) LVDS differential data input (B port)
LVDS
LVDS
RBIN1+ Positive (+) LVDS differential data input (B port)
10
11
12
13
14
15
16
17
18
19
20
Vss
RBIN2-
Gnd
Negative (-) LVDS differential data input (B port)
LVDS
LVDS
RBIN2+ Positive (+) LVDS differential data input (B port)
Vss
CKBIN-
CKBIN+ Positive (+) LVDS differential clock input (B port)
Vss
RBIN3-
RBIN3+ Positive (+) LVDS differential data input (B port)
Vss
SELLVDS
Gnd
Negative (-) LVDS differential clock input (B port)
LVDS
LVDS
Gnd
Negative (-) LVDS differential data input (B port)
LVDS
LVDS
Gnd
Select LVDS data order 【Note2】
Pull Up
【Note2】This module has dual pixel port to receive dual pixel data at the same time . A port receives first
pixel data and B port receives second pixel data in dual pixel data.
LD-14115-4
【Note2】SELLVDS(Thine:THC63LVDM83R)
Transmitter
SELLVDS
=L
R0(LSB)
R1
Pin No
51
52
54
55
56
3
Data
TA0
TA1
TA2
TA3
TA4
TA5
TA6
TB0
TB1
TB2
TB3
TB4
TB5
TB6
TC0
TC1
TC2
TC3
TC4
TC5
TC6
TD0
TD1
TD2
TD3
TD4
TD5
TD6
=H
R2
R3
R4
R5
R2
R3
R4
R5
R6
R7(MSB)
G2
G0(LSB)
G1
4
6
7
G3
G4
G5
G6
G2
G3
G4
G5
11
12
14
15
19
20
22
23
24
27
28
30
50
2
G7(MSB)
B2
B0(LSB)
B1
B3
B4
B5
B6
B2
B3
B4
B5
B7(MSB)
(NA)
(RSV1)
DE
R0(LSB)
R1
G0(LSB)
G1
B0(LSB)
B1
(NA)
(RSV1)
DE
R6
R7(MSB)
G6
G7(MSB)
B6
B7(MSB)
(NA)
8
10
16
18
25
(NA)
LD-14115-5
4-2 Interface block diagram
Using receiver：Contained in a control IC.
Corresponding Transmitter：THC63LVDM83R(THine electronics),DS90C383,DS90C383A(National semiconductor)
（Computer side）
(TFT-LCD side)
8
RAIN0+(5)
RA0～RA7
8
8
8
8
RA0～RA7
GA0～GA7
BA0～BA7
RAIN0-(6)
GA0～GA7
RAIN1+(8)
RAIN1-(9)
RAIN2+(11)
RAIN2-(12)
8
BA0～BA7
RAIN3+(17)
DEA
CLK
RAIN3-(18)
DEA
CLK
RACLKIN+(14)
PLL
PLL
RACLKIN-(15)
A Port
B Port
RBIN0+(5)
RBIN0-(6)
8
RB0～RB7
GB0～GB7
BB0～BB7
8
8
8
RB0～RB7
GB0～GB7
BB0～BB7
8
8
RBIN1+(8)
RBIN1-(9)
RBIN2+(11)
DEB
TxIN18~20
RBIN2-(12)
RBIN3+(17)
DEB
RBIN3-(18)
RBCLKIN+(14)
RBCLKIN-(15)
PLL
PLL
LD-14115-6
< SELLVDS= Low >
1 cycle
CKAIN+
CK^AIN-
RAIN0+
RAIN0-
RA1
GA2
BA3
RA7
RA0
GA1
BA2
RA6
GA0
BA1
DEA
NA
RA5
BA0
NA
RA4
GA5
NA
RA3
GA4
BA5
GA7
RA2
GA3
BA4
GA6
RA1
GA2
BA3
RA7
RA0
GA1
BA2
RA6
GA0
RAIN1+
BA1
DEA
NA
RAIN1-
RAIN2+
RAIN2-
RAIN3+
RAIN3-
BA7
BA6
Tcsq
CKBIN-
CKBIN+
RBIN0+
RBIN0-
RB1
GB2
BB3
RB7
RB0
GB1
BB2
RB6
GB0
BB1
DEB
NA
RB5
BB0
RSV1
BB7
RB4
RB3
GB4
BB5
GB7
RB2
GB3
BB4
GB6
RB1
GB2
BB3
RB7
RB0
GB1
BB2
RB6
GB0
BB1
DEB
NA
RBIN1+
GB5
NA
RBIN1-
RBIN2+
RBIN2-
RBIN3+
RBIN3-
BB6
DE: Display Enable
RSV1: Reserve (Fixed GND)
NA: Not Available
LD-14115-7
< SELLVDS= High >
1 cycle
CKAIN+
CKAIN-
RAIN0+
RAIN0-
RA3
GA4
BA5
RA1
RA2
GA3
BA4
RA0
GA2
BA3
DEA
NA
RA7
BA2
NA
RA6
GA7
NA
RA5
GA6
BA7
GA1
RA4
GA5
BA6
GA0
RA3
GA4
BA5
RA1
RA2
GA3
BA4
RA0
GA2
RAIN1+
BA3
DEA
NA
RAIN1-
RAIN2+
RAIN2-
RAIN3+
RAIN3-
BA1
BA0
Tcsq
CKBIN-
CKBIN+
RBIN0+
RBIN0-
RB3
GB4
BB5
RB1
RB2
GB3
BB4
RB0
GB2
BB3
DEB
NA
RB7
BB2
RSV1
BB1
RB6
RB5
GB6
BB7
GB1
RB4
GB5
BB6
GB0
RB3
GB4
BB5
RB1
RB2
GB3
BB4
RB0
GB2
BB3
DEB
NA
RBIN1+
GB7
NA
RBIN1-
RBIN2+
RBIN2-
RBIN3+
RBIN3-
BB0
DE: Display Enable
RSV1: Reserve (Fixed GND)
NA: Not Available
LD-14115-8
4-2. Back light driving
CN 1, 2, 3 (Upside)
CN 4, 5, 6 (Downside)
:
:
The module-side connector
The user-side connector
BHSR－02VS－01
SM02B－BHSS－1－TB
Function
(JST)
(JST)
Pin no. symbol
I/O
Ｖhigh
Ｖlow
1
2
I
I
Power supply (High voltage side)
Power supply (Low voltage side)
1pin
1pin
ＣＮ１
ＣＮ２
ＣＮ３
1pin
TFT LCD
1pin
1pin
ＣＮ４
ＣＮ５
ＣＮ６
1pin
5. Absolute Maximum Ratings
Parameter
Symbol Condition
Ratings
Unit
Ｖ
Remark
VI
Ta=25℃
Ta=25℃
－
－0.3 ～ +3.6
0 ～ ＋14.0
－25 ～ ＋60
0 ～ ＋50
Input voltage
SELLVDS
Ｖ
+12.0V supply voltage
Storage temperature
Vcc
Tstg
℃
【Note1】
－
℃
Operating temperature (Ambient) Topa
【Note1】Humidity：95%RH Max. ( Ta≦40℃ )
Maximum wet-bulb temperature at 39℃ or less. ( Ta>40℃ )
No condensation.
LD-14115-9
6. Electrical Characteristics
6-1. TFT-LCD panel driving
Parameter
Ta＝25℃
Symbol Min.
Typ. Max. Unit
Remark
【Note1】
【Note2】
Vcc
Supply voltage
Vcc
Icc
+11.4 +12.0 +12.6 V
－
Current dissipation
390
－
－
－
－
600
mA
－
0
Permissive input ripple voltage
Input voltage (Low)
VRF
VIL
100 mVp-p
+0.6
+3.3
500
V
V
SELLVDS
SELLVDS
SELLVDS
VI=GND
VIH
IIL
Input voltage (High)
+2.7
－
μA
Input current (Low)
IIH
－
－
μA
Input current (High)
100
SELLVDS
VI=Vcc
VOL
VOH
－
－
－
Output voltage (Low)
Output voltage (High)
0.4
V
V
BLON:IOL=-1mA
BLON:IOH=1mA
－
2.4
【Note1】
1）On-off sequences of Vcc and data
Vcc
Vcc
11.4V
11.4V
0＜t1≦60ms
DE,CK ,Data
DE,CK,Data
0＜t2≦10ms
1.0V
1.0V
0≦t3≦1s
t4≧100ms
t3
t4
t1
t2
Vcc
2）Dip conditions for supply voltage
Vmin,Vth=11.4V, 9.6V
1) Vth ≦Vcc＜ Vmin
td≦ 20ms
2) Vcc＜Vth
Vth
Vmin
The LCD module shuts down.
td
RGB
RGB
RGB
GS2
RGB RGB
GS254 GS255
【Note2】 Typical current situation : 256-gray-bar pattern
Vcc=+12.0V
....
GS0 GS1
The explanation of each gray scale ,GS,
is described below section 8.
LD-14115-10
6-2. Back light driving
The back light system is an edge-lighting type with six CCFTs (Cold Cathode Fluorescent Tube).
The characteristics of the lamp are shown in the following table.
The value mentioned below is at the case of one CCFT.
CCFT Model Name：KTBE26MSTF‐A424NE209‐Z‐3（STANLEY.ELECTRIC.CO.,LTD）
Parameter
Lamp current range
Lamp voltage
Symbol
IL
Min.
3.0
Typ.
6.0
790
4.7
60
Max.
6.5
Unit
mArms
Vrms
W
Remark
【Note1】
VL
－
－
30
－
－
－
－
70
Ta=25℃
Lamp power consumption
Lamp frequency
PL
【Note2】
FL
KHz
【Note3】
Kick-off voltage
Vs
1,500 Vrms
2,000 Vrms
－
－
Ta=25℃【Note4】
Ta=0℃【Note4】
Lamp life time
TL
50,000
Hour
【Note5】
－
－
【Note1】 A lamp can be light in the range of lamp current shown above.
Maximum rating for current is measured by high frequency current measurement equipment
connected to VLOW at circuit showed below.
(Note : To keep enough kick-off voltage and necessary steady voltage for CCFT.)
Lamp frequency : 30～70kHz
Ambient temperature : 0～50℃
CN1:1,2,3,4,5,6:
1pin(Vhigh)
Inverter
CN1:1,2,3,4,5,6:
Ａ
Module
～
2pin(Vlow)
【Note2】 Referential data per one CCFT by calculation ( IL × VL ) .
The data doesn’t include loss at inverter .
【Note3】 Lamp frequency of inverter may produce interference with horizontal synchronous frequency, and
this may cause horizontal beat on the display. Therefore, adjust lamp frequency, and keep inverter as far
as from module or use electronic shielding between inverter and module to avoid interference.
【Note4】Kick-off voltage value is described as the index in the state of lamp only.
The kick-off voltage is estimated to be risen up as approx. +200V in the state of module only, and the
further rise up can be seen according to the assembling status of user cabinet. Please set the kick-off
voltage of inverter to avoid the lighting failures in the state of operation. Please design the inverter so
that its open output voltage can be connected for more than 1 second to startup. Otherwise, the lamp
may not be turned on. But, please set as 100ms when the ambient luminance around the lamp is more
than 1lux.
【Note5】 Lamp life time is defined as the time when either ① or ② occurs in the continuous operation under
the condition of Ta=25℃ and IL=6.0 mArms .
① Brightness becomes 50% of the original value under standard condition.
② Kick-off voltage at Ta=0℃ exceeds maximum value,2000Vrms .
《Note》
The performance of the backlight, for example lifetime or brightness, is much influenced by the characteristics
of the DC-AC inverter for the lamp. When you design or order the inverter, please make sure that a poor lighting
caused by the mismatch of the backlight and the inverter (miss-lighting, flicker, etc.) never occurs. When you
confirm it, the module should be operated in the same condition as it is installed in your instrument.
Use the lamp inverter power source incorporating such safeguard as overvoltage / overcurrent protective circuit
or lamp voltage waveform detection circuit, which should have individual control of each lamp.
In case one circuit without such individual control is connected to more than two lamps, excessive current may
flow into one lamp when the other one is not in operation.
Synchronize frequency and phase of two CCFT in the same connector.
Otherwise it may exceed rated voltage of connector.
LD-14115-11
7. Timing characteristics of input signals
7-1-1. Timing characteristics
Parameter
Symbol
1/Tc
Min.
60.0
–4
Typ.
81.0
0
Max.
85.0
4
Unit
MHz
ns
Remark
Clock
Frequency
Skew
【Note1】
Tcsq
TH
Data enable Horizontal period
signal
830
1080
13.3
800
1600
－
clock
µs
10.0
800
Horizontal period (High)
THd
TV
800
2000
－
clock
line
ms
【Note2】
Vertical period
1205
12.1
1200
1250
16.7
1200
Vertical period (High)
TVd
1200
line
【Note1】 Lvds (A port)– Lvds (B port) phase difference
【Note2】 In case of using the long vertical period, the deterioration of display quality, flicker etc. may occur.
TH
THd
DEA,DEB
DA
1
3
4
1
(RA,GA,BA)
1599
1599
DB
(RB,GB,BB)
2
2
1600
Tc
1600
1
2
1200
DEA,DEB
1199
TVd
TV
DEA
DEB
Tcsq
LD-14115-12
7-2 Input Data Signals and Display Position on the screen
Graphics and texts can be displayed on a 1600 × 3× 1200 dots panel with 16M colors by supplying
48 bit data signal (8bit/color [256 gray scales] × 3 × 2 pixels).
RA GA BA RB GB BB
Two pixel-data are sampled at the same time.
DA(1,1)
DB(2,1)
＊DA： RA0～RA7, GA0～GA7, BA0～BA7
＊DB： RB0～RB7, GB0～GB7, BB0～BB7
DA(1,1) DB(2,1)
DA(1,2) DB(2,2)
DA(1,3)
DA(3,1)
DB(1600,1)
Ｒ Ｇ Ｂ
DA(1,1200)
DB(1600,1200)
Display position of input data（H,V）
LD-14115-13
8. Input Signals, Basic Display Colors and Gray Scale of Each Color
Data signal
Colors & Gray RA0 RA1 RA2 RA3 RA4 RA5 RA6 RA7 GA0 GA1 GA2 GA3 GA4 GA5 GA6 GA7 BA0 BA1 BA2 BA3 BA4 BA5 BA6 BA7
Gray scale Scale RB0 RB1 RB2 RB3 RB4 RB5 RB6 RB7 GB0 GB1 GB2 GB3 GB4 GB5 GB6 GB7 BB0 BB1 BB2 BB3 BB4 BB5 BB6 BB7
Black
Blue
－
－
－
－
－
－
－
－
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Green
Cyan
Red
Magenta
Yellow
White
Black
ꢀ
GS0
GS1
GS2
ꢁ
0
1
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Darker
ꢀ
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
ꢂ
ꢁ
Brighter GS250
1
0
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ꢂ
GS251
GS252
Red
Black
ꢀ
GS0
GS1
GS2
ꢁ
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Darker
ꢀ
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
ꢂ
ꢁ
Brighter GS250
GS251
Green GS252
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ꢂ
Black
ꢀ
GS0
GS1
GS2
ꢁ
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Darker
ꢀ
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
ꢂ
ꢁ
ꢁ
Brighter GS250
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ꢂ
GS251
GS252
Blue
0 : Low level voltage,
1 : High level voltage.
Each basic color can be displayed in 256 gray scales from 8 bit data signals. According to the combination of
total 48 bit data signals, the 16-million-color display can be achieved on the screen.
LD-14115-14
9. Optical Characteristics
Parameter
Ta=25℃, Vcc =+12V
Remark
Symbol
θ11
θ12
θ21,θ22
ＣＲ
τd
Condition
Min.
70
Typ.
85
Max.
－
Unit
Deg.
Deg
CR≧10
Viewing
Vertical
【Note1,4】
Angle range
－
70
85
－
Horizontal
70
85
Deg.
θ=0°
－
－
Contrast ratio
350
5
【Note2,4】
－
ｍｓ
ｍｓ
－
Response
Time
Rise
25
【Note3,4】
τr
－
Decay
20
50
0.283
0.313
0.343
Chromaticity of
Wx
【Note4】
0.329
white
Chromaticity of
red
－
Wy
0.299
0.608
0.309
0.250
0.570
0.114
0.057
0.359
0.668
0.369
0.310
0.630
0.174
0.117
－
Rx
0.638
0.339
0.280
0.600
0.144
0.087
－
Ry
－
Chromaticity of
green
Gx
－
Gy
－
Chromaticity of
blue
Bx
－
By
Luminance of white
YL
cd/m2
IL=6.0mA rms
【Note4】
－
180
220
δw
－
－
－
White Uniformity
1.25
【Note5】
The measurement shall be executed 30 minutes after lighting at rating.
※
The optical characteristics shall be measured in a dark room or equivalent state with the method
shown in Fig.2 below.
Photodetector
Contrast ratio/Response Time(BM-5A)
Luminance(BM-7)
Chromaticity(SR-1)
Photodetector(EZ-CONTRAST）
４００mm
Field=２°
Center of screen(θ=0°）
Center of screen(θ=0°)
TFT-LCD-Module
TFT-LCD-Module
Fig2-2 Luminance/Contrast ratio/Response time/Chromaticity
measurement method
Fig2-1 Viewing angle measurement method
Fig2 Optical characteristics measurement method
LD-14115-15
【Note1】Definitions of viewing angle range:
【Note2】Definition of contrast ratio:
The contrast ratio is defined as the following.
Luminance (brightness) with all pixels white
Luminance (brightness) with all pixels black
Contrast Ratio (CR) ＝
【Note3】Definition of response time:
The response time is defined as the following figure and shall be measured by
switching the input signal for "black" and "white".
【Note4】This shall be measured at center of the screen.
【Note5】Definition of white uniformity:
White uniformity is defined as the
following with five measurements
(A～E).
400
800
1200 pixel
A
B
D
E
300
600
C
900
pixel
Maximum Luminance of five points (brightness)
Minimum Luminance of five points (brightness)
δw＝
LD-14115-16
10. Handling Precautions
a) Be sure to turn off the power supply when inserting or disconnecting the cable.
b) Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or
twist.
c) Since the front polarize is easily damaged, pay attention not to scratch it.
d) Since long contact with water may cause discoloration or spots, wipe off water drop immediately.
e) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
f) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. Handle with
care.
g) Since CMOS LSI is used in this module, take care of static electricity and take the human earth into
consideration when handling.
h) Make sure the mounting holes of the module are grounded sufficiently. Take electro-magnetic interference
(EMI) into consideration.
i) The module has some printed circuit boards (PCBs) on the back side. Take care to keep them form any
stress or pressure when handling or installing the module; otherwise some of electronic parts on the PCBs
may be damaged.
j) Observe all other precautionary requirements in handling components.
k) When some pressure is added onto the module from rear side constantly, it causes display non-uniformity
issue , functional defect, etc. So, please avoid such design.
l) If the stress is applied onto the panel under operating conditions, display defects such as black dots may
occur. So, do not press the display with fingers.
To recover this defect, turn off the power supply and restart after several seconds.
11. Packing form
a) Piling number of cartons : maximum 8 cartons
b) Packing quantity in one carton : 2 module
c) Carton size : 592mm(W) × 486mm(H) × 215(D)
d) Total mass of one carton filled with full modules : 10.5kg
e) Packing form is shown in Fig.3
LD-14115-17
12．Reliability test items
No. Test item
Conditions
Ta=60℃
Ta=-25℃
240h
240h
1
2
3
High temperature storage test
Low temperature storage test
High temperature
Ta=40℃ ; 95%RH 240h
& high humidity operation test
High temperature operation test
(No condensation)
Ta=50℃
(The panel temp. must be less than 60℃)
Ta=0℃ 240H
240h
4
5
6
Low temperature operation test
Vibration test
Frequency : 10～57Hz/Vibration width (one side) : 0.075mm
: 58～500Hz/Gravity : 9.8m/s2
Sweep time : 11 minutes
(non- operating)
Test period : 3 hours
(1 hour for each direction of X,Y,Z)
Max. gravity : 490m/s2
7
Shock test
(non- operating)
Pulse width : 11ms, sine wave
Direction : ±X, ±Y, ±Z,
once for each direction.
【Result Evaluation Criteria】
Under the display quality test conditions with normal operation state, these shall be no change
which may affect practical display function.
LD-14115-18
13．Others
1) Lot No. and indication Bar Code Label:
SHARP
LQ201U1LW01
How to express Lot No.
Model No.
A production year
(the last figures of
the Christian Era)
Bar Code(Lot No.)
Lot No.
Serial No.
23 XXXXXX
MADE IN JAPAN
A production month (1～9,X,Y,Z)
2) Packing Label
① Model No. (LQ201U1LW01) ② Lot No. (Date) ③ Quantity
社内品番：（４Ｓ）LQ201U1LW01
Bar Code（①）
ＬｏｔＮＯ． ：（１Ｔ）２００２．０３．０１
Bar Code（②）
Ｑｕａｎｔｉｔｙ：（Ｑ） ２ ｐｃｓ
Bar Code（③）
ユーザ品番 ：
シャープ物流用ラベルです。
3) Adjusting volume have been set optimally before shipment, so do not change any adjusted value.
If adjusted value is changed, the specification may not be satisfied.
4) Disassembling the module can cause permanent damage and should be strictly avoided.
5) Please be careful since image retention may occur when a fixed pattern is displayed for a long time.
6) The chemical compound that causes the destruction of ozone layer is not being used.
7) Warning of mercury and material information of LPG(Light Pipe Guide) are labeled on the back of the
module.
MATERIAL INFORMATION
>PLASTIC LIGHT GUIDE:PMMA<
COLD CATHODE FLUORESCENT LAMP IN LCD PANEL
CONTAINS A SMALL AMOUNT OF MERCURY,PLEASE FOLLOW
LOCAL ORDINANCES OR REGULATION FOR DISPOSAL
当該液晶ディスプレイパネルは蛍光管が組み込まれていますので、地方自
冶体の条例、または、規則に従って廃棄ください。
8) When any question or issue occurs, it shall be solved by mutual discussion.
LD-14115-19
14．Carton storage condition
Temperature
0℃ to 40℃
Humidity
95%RH or less
Reference condition : 20℃ to 35℃ , 85%RH or less (summer)
5℃ to 15℃ , 85%RH or less (winter)
:
・the total storage time (40℃,95%RH) : 240H or less
Sunlight
Be sure to shelter a product from the direct sunlight.
Atmosphere
Harmful gas, such as acid and alkali which bites electronic components and/or
wires, must not be detected.
Notes
Be sure to put cartons on palette or base, don’t put it on floor, and store them with
removing from wall.
Please take care of ventilation in storehouse and around cartons, and control
changing temperature is within limits of natural environment.
1 year
Storage period
LD -14115-20
LD -14115-21
LD -14115-22
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited
Warranty for SHARP’s product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied.
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND
FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or in any way responsible,
for any incidental or consequential economic or property damage.
NORTH AMERICA
EUROPE
JAPAN
SHARP Corporation
SHARP Microelectronics of the Americas
5700 NW Pacific Rim Blvd.
Camas, WA 98607, U.S.A.
Phone: (1) 360-834-2500
Fax: (1) 360-834-8903
SHARP Microelectronics Europe
Division of Sharp Electronics (Europe) GmbH
Sonninstrasse 3
20097 Hamburg, Germany
Phone: (49) 40-2376-2286
Fax: (49) 40-2376-2232
Electronic Components & Devices
22-22 Nagaike-cho, Abeno-Ku
Osaka 545-8522, Japan
Phone: (81) 6-6621-1221
Fax: (81) 6117-725300/6117-725301
Fast Info: (1) 800-833-9437
TAIWAN
SINGAPORE
KOREA
SHARP Electronic Components
(Korea) Corporation
RM 501 Geosung B/D, 541
Dohwa-dong, Mapo-ku
Seoul 121-701, Korea
SHARP Electronic Components
(Taiwan) Corporation
8F-A, No. 16, Sec. 4, Nanking E. Rd.
Taipei, Taiwan, Republic of China
Phone: (886) 2-2577-7341
SHARP Electronics (Singapore) PTE., Ltd.
438A, Alexandra Road, #05-01/02
Alexandra Technopark,
Singapore 119967
Phone: (65) 271-3566
Phone: (82) 2-711-5813 ~ 8
Fax: (82) 2-711-5819
Fax: (886) 2-2577-7326/2-2577-7328
Fax: (65) 271-3855
CHINA
HONG KONG
SHARP Microelectronics of China
(Shanghai) Co., Ltd.
SHARP-ROXY (Hong Kong) Ltd.
3rd Business Division,
28 Xin Jin Qiao Road King Tower 16F
Pudong Shanghai, 201206 P.R. China
Phone: (86) 21-5854-7710/21-5834-6056
Fax: (86) 21-5854-4340/21-5834-6057
Head Office:
17/F, Admiralty Centre, Tower 1
18 Harcourt Road, Hong Kong
Phone: (852) 28229311
Fax: (852) 28660779
No. 360, Bashen Road,
Xin Development Bldg. 22
Shenzhen Representative Office:
Room 13B1, Tower C,
Waigaoqiao Free Trade Zone Shanghai
200131 P.R. China
Electronics Science & Technology Building
Shen Nan Zhong Road
Email: [email protected]
Shenzhen, P.R. China
Phone: (86) 755-3273731
Fax: (86) 755-3273735
|